DEN204KA Norge Dryer - Instructions

Had to disassemble most of the dryer including pulling dryer drum in order to get to drum support rollers. Not a real difficult repair, just time consumming because of amount of parts needing to be removed inorder to get to rollers.

popped front off took blower front off took fan off put new one on replaced cover & front. job done. ordered fan on thursday got it on friday great service.

Finally got tired to greasing the wheels only to have to do it again so I sprung for new wheels and shafts. Popped the top open, removed the drum, installed the two new shafts with supplied screws then attached the wheels. Figured I'd change out the original belt while I was at it even though the old one still looked good. It's nice and quiet again, plus it give me a chance to clean it out.

Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

googled"dryer not heating". landed on partsselect.com. checked parts like website said with multimeter. pointed to thermostat. ordered it, replaced it, it works now.

My part came a day or so after the order was placed. There was really no installation required, but I will definitly make orders from this site again. Thank you very much!

Unplug - use screwdriver to release top latches.
Raise top to more than 90 degrees - hard on hands or head if it falls. Remove wires from door swithch and remove front panel screws, lift off front cover. Remove screws from front paned of blower housing. Remove snap ring - shaft clamp already loose, remove old blower whee and install new one. Use DEEP(spark plug) socket tap new wheel onto shaft, replace clamp and snapring and reinstall panel on housing, put front panel back-install door switch wires before screws, replace top, plug in and test run.(note 1st word correction)

After reading everyone else's comments I started by pulling out the dryer, unplugging the power and exhaust. Next moved the dryer to an area where I had room to lay it on the back. Then using a flat blade screw driver, I popped the top attached tape to the top so I could lean back the top without having to hold it. Removed the two screws from the front panel and removed the door safety shut off before removed the front panel. Then I layed the dryer on its back. Then reached under the drum, pushed the belt tensioner toward the motor puller to release the tension on the belt. Then slid the belt to the base. Pulled the drum up and out of the cabinet. Next I cleaned all the lint and crud out of the dryer components. To remove the clips that hold the rollers in place, I use 2 small flat blade screw drivers. These are inserted at the back side of the horse show shaped clip between the shaft and the clip. When the two screw drivers are rotated like turning a screw they slide the clip out. Next I used a socket wrench with a #8 metric socket(I didn't have the sae size) and removed the screws holding the drum roller brackets. I simply reversed the procedure to install the new rollers. Since the dryer was on its back, when I put the drum back in, its own weight slipped it in place. Then pulled the belt around the drum and between the motor pulley and the belt tensioner. Holding the belt with one hand, I used the other hand to pushed the belt tensioner in and positioned the belt. Then I stood the unit back upright and put the front cover on, replaced the door safety switch, removing the tape holding the lid and then cloed the lid. Of course I put the dryer back in place, leveled it, and it now runs like brand new. My thanks to every one else who gave me hints that saved be about $450!

Had a problem holding drum in place and putting front back on. Got it together and drum wouldn't turn. Had to tear it a part again and belt had turned.

Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time) and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.

It was easy. Just removed the old seal and plugged the new one in place. Took less than 3 minutes

I just followed your video how to replace a broken belt , after viewing replacing belt went easy

watched your video on 'how to' and did it like man showed..no problem

First I removed the screws of the dryer cover. Next removed the screws holding the dryer drum.

Drilled out the two rivets left from the old glide. Inserted the plastic and postitioned the cushion underneath. Inserted the new glide and drilled a hole in the plastic to accomodate the new rivet. Inserted rivet. Pulled the other end so it was tight holding the cushion and did the other end. Done.

Had to cut the glide 1/4 '' of the width to slide it through the existing slots in the panel.