DEN202W Norge Dryer - Instructions

Tools and materials:

#2 Philips head screw driver
Standard flat-tip screw driver
1/4" nut driver or ratchet
1/4" drive sockets: 1/4, 5/16
Something 3-4 inches thick to wedge under drum for support (i.e. scrap 4x4, soap bottle, books)

Replacement Procedures:

1. Unplug dryer from wall outlet
2. Pull out lint screen
3. Remove 2 Philips screws attaching lint trap to dryer top
4. Lift hinged dryer top panel near front and lean it back on wall. You may need to pry between side panels and top with flat-tip screw driver to get it started.
5. Disconnect plug from dryer door switch near front
6. Remove two 1/4" and two 5/16" hex screws inside front panel near top.
7. Open dryer door and lift front panel straight up to disengage tabs from slots near bottom of front panel.
8. While supporting drum with one hand, lift front panel and set aside with other hand.
9. Slip replacement belt around drum with ribs facing drum and position it where old belt left its mark.
10. Wedge something under drum to support it while installing the belt.
11. Re-position tensioner in two slots in bottom panel just in front of motor. On my model the bend in the spring will be on the right side with the idler pulley to the left, when viewed from the front.
12. Ensuring the belt isn't twisted, thread a small loop of it through the opening in the tensioner just below the pulley.
13. With the left hand, push against the tensioner spring while working the loop over the drive pulley.
14. While supporting drum with one hand, remove whatever you put under the drum to support it.
15. Replace front panel by aligning the slots with the tabs near the bottom and lowering it into place.
16. Carefully slip the drum opening over the flange on the front panel and replace hex screws.
17. Slowly roll the drum in one direction or the other until the belt aligns and centers itself.
18. Re-connect the plug for the dryer door switch.
19. Lower the dryer top and press until it snaps back into place.
20. Replace philips screws to secure lint trap and replace lint screen.
21. Plug dryer back into wall outlet, close door, set to dry, and press start.

Needed a belt. Only snag was for me was re-installing front panel (door)

Watched a video and went to town taking it apart. I stuck a pop can under the barrel to hold it up while I worked on pulleys. My dryer does not have a plastic pulley but a metal tension bar with a hole in the middle. Ran upstairs and watched a different video with my set up and all was good. 5 min of work 5 min watching Youtube and 5 min cleaning all the lint out of the machine. I am actually glad the old belt broke because some of the lint was in a clump and had scorch marks on it. I took the shop vac to every part of the cabinet and shoved it down the lint trap sleeve also.

Just slid the new filter in.

Watched the video on the site and it was spot-on! Super-easy, took like 10 minutes to replace the belt. Thanks!

Disconnect power. Removed front panel and lifted top. Removed belt around spring pully and motor assembly. Carefully eased belt around back of drum and gasket. Reverse process.

Removed the two screws at the back that hold the top of the dryer. Then I pried off the top at the front by inserting a screwdriver into the front to remove the top from the clips. Then I tilted up the top like a car hood.

I removed the two screws inside that held the front on and lifted the front off. Because of the wires attached to the front, I made sure to turn the front aside without pulling on the wires. After removing the broken belt, I put the replacement belt over the front of the drum, lifting the drum a little. Then I threaded the belt over the drive and around the tension wheel per a diagram I found on the web.

While I had the front off, I removed the lint trap and cleaned out probably decades worth of lint.

Then I replaced all the parts in reverse order, plugged it in and had a working dryer!

I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.

I replaced it

First let me say that the video provided was wonderful, I followed the instructions on the video, & it worked great, no problems at all. Saved me from paying huge costs from a repairman.

Lifted the top, then removed two screws holding on front panel, then removed cover holding this part in place, then used retaing ring plyers to remove the ring, then plyers to remove wheel clamp, took off the blower wheel. After that did everything in reverse to put it back together. And now the dryer is quite.

- Unplug the electric dryer.
- Manually opened the top of the dryer.
- Unclipped the wire assembly attached to the front panel of the dryer.
- Removed two screws holding the front panel of the dryer, and remove front panel for access.
- Very Important!! Note how the old dryer is currently installed before proceeding.
- Rotated the dryer drum while working the dryer belt toward the rear of the dryer.
- Removed the dryer drum.
- Removed the old dryer belt.
- Put the new dryer belt around the dryer drum and put the dryer drum back onto the drum rollers and into the rear guides.
- Here's the hard part, lay on floor and reach into the pulley area and motor - wrap new dryer belt around these belt rollers as "noted" in the fifth step.
- Rotate dryer drum by hand to ensure the new dryer belt is exactly installed as the old dryer belt.
- Reinstall front panel.
- Reclip wire assembly onto the front panel.
- Manually close the top of the dryer.
- Plug in the electric dryer.

Step 1. Read all the comments about how to do this job in this forum. (i found them very useful)

Step 2. Read the directions that come with the dryer (they helped a lot)

Step 3. Don't forget to disconnect the power cord before reattaching the door switch wires (oucH! ) or doing anything with your dryer.

First, I unplugged the dryer. I pulled up the lint filter, then unscrewed the two screws there. Then pulled up the top panel. I had a helper hold it up since it couldn't lean against the wall. Then I had to take the front panel off the dryer. The idiots at Kenmore used screws, not pins, so I needed to use a socket wrench to get those two out of the top corners. Then I lifted it up and off. I removed the broken belt. I put in the new one. I replaced the pulley, which had fallen without the tension of the belt holding it in place. It was pretty easy to figure out how it went, but I consulted the online community for a diagram. I threaded the belt in place, replaced the panels, and viola! It worked. Easy.

0) unplugged the dryer
1) lifted the top which put up a bit of a fight
2) removed a screw on each side of the front panel near the top
3) picked off the front panel from the lower clips
4) removed panel from in front of the blower
5) removed clip and snap rig
6) removed old blower and installed new one
7) reversed the disassembly procedure
This is the second replacement blower for this dryer. This blower was a much tighter fit than the first replacement so maybe the inner flat that the motor drives with will last longer. I actually had to pound the new blower onto the motor shaft.