DGJ204A Norge Dryer - Instructions

the video was very well done and able to understand. disconnect power ,remove lint trap,remove 2 phillps head screws, push putty knife in front seam line about 1'' in from corners to release top assembly ,lift up and support, disconnect wire connector ,remove 1 screw in each front corner lift front panel off while holding drum, remove broken belt,install new belt with grooves against drum ,feed around tensioner pulley and onto motor shaft pulley ,spin drum by hand to make sure belt tracking etc. reassembly in reverse.

I suspected the high limit fuse. I unplugged the machine, lifted the top, found the high-limit fuse (about the size of four dimes glued together) just to the right of the heating coil. I pulled the two wires off and taped them together. Plugged the machine back in and it worked perfectly. I made sure the heating coils started to glow red. When the part arrived, I replaced the old unit with the new, plugged the two wires back on, and I was done. Just for additional information, when I touched the heating coil during the repair, it broke. After 16 years, the heating coils get brittle, so I also replaced the heating coil and it's thermostat just above it (about the size of 6 quarters glued together). I hope this gets me another 16 years.

I opened up the dryer lifting the lid with a putty knife and removed the two screws holding the front. I reached in and removed the belt and removed the drum. I took my shop vac and cleaned all the lint, the door passage to the lint screen extremly full of hard lint. I tested the coils with my multi meter and they tested bad. I also did the test that was suggested by Part Select and again it showed the coils as bad. Once I received the parts about three days, it only took about twenty minutes to install using just a screw driver to replace the coils and the belt went on real easy with easy access to the tentioner. and my dryer now runs more quiet and dries the clothes in half the time it used to take. My belt was still in pretty good shape but I put a new one on since I had it apart any way. My friend had the same problem with his dryer and spent $300.00 for a repairman to do the same thing. I tried to tell him it is not rocket science and very easy to do yourself. Thank you Part Select for the good repair advice as well as the timely delivery of the parts.

I took apart the dryer by unscrewing the top and the front, front comes off by just undoing the two top screws on the inside. I figured it was something to do with the rollers since the noise was ciclycal. The hardest part was to put the drive belt back on. It helps to have a second person for about 5 minutes.

Lifted top from dryer and fuses were in the back of drum just below heating coil. Used nut driver to remove heating coil to gain access to fuses and replaced them. Process was quick and easy. Diagram from this site made locating fuses elementary!

P.S. I have no certified experience in appliance repair.This was my first time ever and dryer works perfect.

I just removed 1 screw that held the safety thermostat in and replaced it. Then I removed the long screw that holds the heating element and the high limit fuse in place. Replaced the fuse, cleaned out the lint duct area. Closed the dryer lid and pluged it in, it worked fine.

i followed part select instructions that probable cause was either thermal fuse or high limit thermostat.put ohm meter across both & saw thermal fuse(has pink dot on it) part 53-1182 was open.ordered thermal fuse replacement kit. part#LA-1053. the problem i had was after reaching down the side of heating housing removing the bracket with the thermal fuse,replacing & reconnecting it i had a hard time reinstalling the bracket,very tight space & i don't have very big hands.finally got the fuse in it's hole in the bracket & slid & jammed the bracket into the side of the mounting housing & it stayed secure.dryer started

The dryer was not difficult to repair. The diagram that came with the belt made the repair easy. The repair part came in a very timely manner.

Disconnected power....lifted the top of the dryer to gain access to parts requiring replacement... Unsrcewed two screws 1/4 inch nutdriver....disconnected the two wires...connected the wires to the new part and attached screws...Removed 1 screw from heat element and raised element to get to heat sensor...sensor pops out removed wires and popped new sensor in...replaced wires closed top lid reconnected power source and started dryer

Ordered belt, received it two days later. It was a perfect fit.
The top of my dryer pops up from the front where 2 screws will allow the front to drop to the ground. Lift the drum slightly to get the belt on. Had to wrestle with the idler arm for about five minutes, but I won.

I ordered the part. This is now my third order. It appears that every 10-12 months this happens. I opened the top of the dryer by using a flat head screw driver to push in two clips. The clips are along the front edge of the lid about two inches in from each side. Push in with the screw driver while pulling up the lid. Once the lid is open (of course the plug is pulled) I locate the heat coil. Above the heat coil is the the thermostat, I replace that. Or maybe it is the over heat fuse, I forget. I then replace the sensor found along the side of the heat coil. Re-attach wires. Close lid. Plug back in and ready to go.

First I opened the top of the dryer, then removed the bracket holding the high limit thermostat. Then I removed the heating element to gain access to the thermal fuse. Installation was the reverse. I also cleaned out the lint trap on the front of the dryer and also checked the vent duct (it is cleaned every year). Very easy repair.

First we removed the front panel then the door. Removed the old coils and put in the new coils, oh yeah don't forget to disconnect the power supply first. Sure enough that was all it took and it runs great. You really can fix your own appliance if you take the time to do some research.

Removed the two screws holding in the Filter and removed the filter.

Removed the two screws holding the front onto the dryer.

Put the belt over the drum and proped the drum up.

Reseated the tension spring and pully in the proper slot. (On my machine it is the position closest to the motor).

Reassembled the dryer in the reverse order.

Pry the front of the top up - it's held on with barbed fasteners that just snap out. Underneath the hood against the back panel is the heating coil assembly. On top of it is the thermostat, hanging from the side of it is the thermal fuse. I removed the heating elements (coiled wires held in frame) to make access to the other parts easier.
Pretty much plug-n-play. One nut driver takes off everything, you might need a needle-nosed pliers to push the lugs onto the contacts of the replacement parts (they fit VERY snugly).

Also, remove the front panel and clean out the lint in the air duct - lint collecting there is apparently what drives up the temp causing the fuse to blow in the first place.