DEP223V Norge Dryer - Instructions

The part didnt line up with the timer markers.

Instructions said where toscrewed it to the machines but didn't match the on and off buttons.

Rotated it and it fit a little better but it still didn't match the minutes or on and/off for every section.

Had to drill a hole in it to screw it in as well cause the ones that came drilled were not lined up right.

removed screws on back plare and replaced heater element. Thank you very much foe your quick delivery of the part I ordered. I was reall;y schocked to see how fast the part arrived. I will recommend your site to anyone who needs parts like I did,.
Thany you Very Much,
Alan Brooks

First I disconnected power to dryer. Next step was to lift top of cabinet and support upright. Then I removed door switch and 2 screws that hold front panel on and set front panel aside. Next was to reach under drum by belt tightener and remove drum drive belt from tightener and pulley of drive motor. Then slowly remove drum from cabinet . Once removed, I could remove old glides that were worn out and install the new ones. Before putting everything back together, I gave the cabinet a thorough vacuuming to remove all lint built up inside, checked electrical connections on heating unit and oiled back drum support rollers and belt idler roller. Next just reassembled everything in reverse order as was disassembled. Plugged cord back in and tested unit to make sure everything sounded good before drying any clothes.

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

Took the front of dryer apart removed belt and drum replaced my parts and reassembled.

popped front off took blower front off took fan off put new one on replaced cover & front. job done. ordered fan on thursday got it on friday great service.

Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

I just used screw driver to pop of clip put new roller on poped clip back on

My part came a day or so after the order was placed. There was really no installation required, but I will definitly make orders from this site again. Thank you very much!

When online& found website... trouble shot for problem per previous posts on PART SELECT.GREAT SITE for problem ifo.I ordered parts,they arrived 2 days later and within 1/2 an hour I had our dryer repaired and working like new!!THANKS!!!

Very simple-remove 3 screws that hold the Control Panel on, remove the two connectors and replace with new part in reverse order. Unfortunately, this did not fix the problem. Will be ordering complete timer assembly.

googled"dryer not heating". landed on partsselect.com. checked parts like website said with multimeter. pointed to thermostat. ordered it, replaced it, it works now.

Finally got tired to greasing the wheels only to have to do it again so I sprung for new wheels and shafts. Popped the top open, removed the drum, installed the two new shafts with supplied screws then attached the wheels. Figured I'd change out the original belt while I was at it even though the old one still looked good. It's nice and quiet again, plus it give me a chance to clean it out.