DEL203A Norge Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stanley from Flushing, NY
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken drive belt
I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bennington, VT
- Parts Used:
- WP53-0771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer would not come up to temp.
Hinged open the top of the dryer. While dryer was running I tapped on the thermostat. The heater came back on. This verified the problem. Unplugged the thermostat, unscrewed it and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LARAMIE, WY
- Parts Used:
- LA-1003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Broken Catch
Watch the video. Very, very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tara from North Canton, OH
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Female End Of The Door Catch Broke
First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Memphis, TN
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The dryer door latch was broken.
The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eli from North Stonongton, CT
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay shut
Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from GORHAM, ME
- Parts Used:
- LA-1006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
drum slide worn out
removed front cover, lifted drum up with a clamp and replaced slides. Replaced front cover
Was this instruction helpful to you?
Thank you for voting!
Noise when running and motor stop. Motor bearing overheated.
Unplug dryer
Pick the top up at the front and swing up. Inside each side of the front is a screw to remove. Do not forget to unhook the door switch wires. Pull the drum. Push belt off as you remove the drum. Works better to reach in at the lower right and take the belt off of the tighener first.
After you clean out any lint in area unplug the wires from the motor and snap off the hold down clamp on the back bearing.
The blower needs to be released fromt he shaft. The snap ring in front of the blower needs to be taken off. This can be done with a screw driver by prying off the flat spot on the shaft. However, a snap ring pliers would be better. The front of the blower housing must come off as the blower must come off. There is a snap ring behind the blower that must come off also.
The biggest problem I had was removing the front motor bearing housing from the plastic blower housing. It is easy once you see that the front bearing housing is held in by four tabs in the plastic housing. By rotating the front bearing housing 90 degrees you will be able to pull it out.
From there just reverse your action. The belt went on ok. I found by putinng the belt on the drum and the motor drive pully first I was able to reach in an put the belt over the tighener.
Pick the top up at the front and swing up. Inside each side of the front is a screw to remove. Do not forget to unhook the door switch wires. Pull the drum. Push belt off as you remove the drum. Works better to reach in at the lower right and take the belt off of the tighener first.
After you clean out any lint in area unplug the wires from the motor and snap off the hold down clamp on the back bearing.
The blower needs to be released fromt he shaft. The snap ring in front of the blower needs to be taken off. This can be done with a screw driver by prying off the flat spot on the shaft. However, a snap ring pliers would be better. The front of the blower housing must come off as the blower must come off. There is a snap ring behind the blower that must come off also.
The biggest problem I had was removing the front motor bearing housing from the plastic blower housing. It is easy once you see that the front bearing housing is held in by four tabs in the plastic housing. By rotating the front bearing housing 90 degrees you will be able to pull it out.
From there just reverse your action. The belt went on ok. I found by putinng the belt on the drum and the motor drive pully first I was able to reach in an put the belt over the tighener.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Livingston, TX
- Parts Used:
- LA-1003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door wasn't staying closed
popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fransisco from Long Branch, NJ
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
there was no heater,the heater doesn't work
I opened the top then i did change the heater element kit only one screw out and finaly replace the temperature switch, again one screw out was realy ease was my first time,the professional online help my, every one can do it thanks i appreciate your help.H.E.K.P/N AH2162280 - temp/switch p/n 31001449.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Wapakoneta, OH
- Parts Used:
- LA-1044
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Low heat in dryer
I suspected (correctly) that the thermostat was malfunctioning so I ordered the Heating Element Kit. This repair would have taken less than 15 minutes if I would not have dropped one of the sheet metals screws in the back of the dryer when re-installing the heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from McCloud, CA
- Parts Used:
- 530106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
blower wheel broke
Lifted hood ,and took two screws and tilted the front back and remove the door switch , and took front off ,use little socket set, took cover off fan housing took pliers removed clamp on fan , remove key way on end ,slid fan off and put new one on and reverse the way if came off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Hardeeville, SC
- Parts Used:
- 530106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
loud bumping on start up, noisy running
Unplugged, loosened front cover, disconnected two wires from door open indicator, removed front cover with screw driver. Removed air flow cover with screw driver. Used pliers and retaining ring pliers to remove old blower wheel, my husband calls it a "squirrel cage". Installed new blower wheel and reassembled. It was all easy to see and get to. Thanks for having the right part. Sue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Boerne, TX
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Dryer would not heat.
removed screws on back plare and replaced heater element. Thank you very much foe your quick delivery of the part I ordered. I was reall;y schocked to see how fast the part arrived. I will recommend your site to anyone who needs parts like I did,.
Thany you Very Much,
Alan Brooks
Thany you Very Much,
Alan Brooks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathtleen from Bristol, CT
- Parts Used:
- WPA3167501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out lightbulb for over 20 years
Unscrewed back plate, and replaced bulb
Was this instruction helpful to you?
Thank you for voting!