8375A REV E Norge Dryer - Instructions

No Repair, just replacement. Went perfect.

I ordered the top 5 items that may cause this problem based on the troubleshooting guide presented by the technicians I found in youtube. I replaced the coils and that fixed the problem. The coils are the first to go out according to techs, but I have the other parts just in case I may need them later on. My Maytag dryer which is over 19 years old is alive and working again. The coils are accessible from the bottom access panel secured by 2 nut screws, unplug the dryer first, then the coils are secured by a bracket with 2 small philips head screw, I used a stubby philips screw driver to remove the bracket, undo the 2 electrical connectors on the coils one with 2 prongs and the other with 3 prongs. Put the new coils attached the electrical connectors and secured them with the bracket. Checked for any loose wiring ensuring connectors are secured in place, then test run the dryer with the panel off so you can see the if the flame stays on, if you run the dryer without wet clothes the flame may stop after 15 or so minutes. It is better to test run the dryer with wet clothes just like when your drying fresh washed and wringed clothes. It was really easy, good luck!

Unscrewed back plate, and replaced bulb

Using a flat-head screw driver, I removed the 1 screw from the small "door" on the back, upper right corner. Once the screw was removed, it allowed the door plate to "pop" open; exposing the old bulb. I removed the old bulb; replaced it with the new one. DONE!

took 2 screws out and replace new coils

Watched youtube video to problem shoot. Cause determined to be coils bad. Searched web found Parts Select to be easiest site to deal with and had coils for best price. Followed instructions supplied with parts. Dryer works like new.

My gas dryer would run with heat for 5 minutes in all settings, but kick off and not heat again. Timer would not advance in autodry. Thought it was the cycling thermostat, so replaced that, but did not solve the issue. Ordered the coils, and cleaned out heavily clogged lint from bottom of lint trap, especially right above the fan motor at the bottom of the trap. Received the coils, opened the top and front, took out drum, and replaced the coils. The replacement took less than 2 minutes. Be careful putting the drum back on to make sure the felt is not caught inside the drum. You can give it a spin to make sure. Wear gloves, as I cut myself up pretty good on the edges of the dryer body. The inside of my dryer looks like a crime scene! Anyway, I put it back together, and it runs great. Solved the timer advance issue in autodry, and the heat kicks on and off when it is supposed to. Good luck! Thanks Part Select!

First I disconnected power to dryer. Next step was to lift top of cabinet and support upright. Then I removed door switch and 2 screws that hold front panel on and set front panel aside. Next was to reach under drum by belt tightener and remove drum drive belt from tightener and pulley of drive motor. Then slowly remove drum from cabinet . Once removed, I could remove old glides that were worn out and install the new ones. Before putting everything back together, I gave the cabinet a thorough vacuuming to remove all lint built up inside, checked electrical connections on heating unit and oiled back drum support rollers and belt idler roller. Next just reassembled everything in reverse order as was disassembled. Plugged cord back in and tested unit to make sure everything sounded good before drying any clothes.

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

i read some of previous customer problems and fixes pulled the front cover off found coil's location when i turned on drier you could see the ignitor getv hot but burner would not ignite unless i put a little pressure on secondary coil when i let go of coil flame would go out. ordered 'M' series new style coil kit came in in about three days installed parts drier workng good i would reuse parts select agian thanks

As many of the other posts here on this website mentioned, I had the same problem of the dryer not heating up. I removed the front panel (4 screws on each side inside of door - easy - followed instructions) and once off I was able to view the igniter glowing properly so I knew the starter/igniter was not the issue. Everything I read then suggested that it must be the two terminal gas valve coil, and sure enough it was. Ordered part -- got it in literally a couple days -- removed bracket (two screws) put in new coil -- turned it on -- works great. Could not have been easier. This is a great website and would recommend it to everyone who is a Do It Yourselfer.

My part came a day or so after the order was placed. There was really no installation required, but I will definitly make orders from this site again. Thank you very much!

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.