7643A REV A Norge Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lou from Weymouth, MA
- Parts Used:
- LA-1053
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer had no power. Internal light was out too.
I followed the "How to" video on your web site. Most importantly, I cleaned the entire filter area which probably caused the problem as your instructions recommended. I will do that annually going forward. I would recommend your service to anyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from Dyer, IN
- Parts Used:
- LA-1008
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Squealing
1.Removed retaining clips,washers,spacer,and cylinder rollers
2.Removed and replaced support assembly
3.Installed spacer
4.Installed cylinder roller assembly
5.Installed washers and retaining clips
This is my second time ordering parts from PartSelect and I am amazed how fast I recieve my orders, which minimizes the downtime of an appliance that's frequently used.
2.Removed and replaced support assembly
3.Installed spacer
4.Installed cylinder roller assembly
5.Installed washers and retaining clips
This is my second time ordering parts from PartSelect and I am amazed how fast I recieve my orders, which minimizes the downtime of an appliance that's frequently used.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Dennisville, NJ
- Parts Used:
- WP31001529
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Had to align tabs on the seal, which are differently spaced, with the holes in the dryer door.
Pulled the old seal off then pushed the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from LEESBURG, FL
- Parts Used:
- LA-1053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
elec.dryer would not start
i followed part select instructions that probable cause was either thermal fuse or high limit thermostat.put ohm meter across both & saw thermal fuse(has pink dot on it) part 53-1182 was open.ordered thermal fuse replacement kit. part#LA-1053. the problem i had was after reaching down the side of heating housing removing the bracket with the thermal fuse,replacing & reconnecting it i had a hard time reinstalling the bracket,very tight space & i don't have very big hands.finally got the fuse in it's hole in the bracket & slid & jammed the bracket into the side of the mounting housing & it stayed secure.dryer started
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Ripley, TN
- Parts Used:
- LA-1053
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
nothing worked no light when door was open
I just removed 1 screw that held the safety thermostat in and replaced it. Then I removed the long screw that holds the heating element and the high limit fuse in place. Replaced the fuse, cleaned out the lint duct area. Closed the dryer lid and pluged it in, it worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Dardenne Prairie, MO
- Parts Used:
- WP31001513
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer worked but no timing.
Part was perfect replacement thanks to online photos. Removed old timer switched leads one at a time from old to new timer and mounted new timer replaced back cover. Everything went fine.
Was this instruction helpful to you?
Thank you for voting!
Motor making rattling noise
Released lid clips, two screws removed to remove the front. Took tension off of the belt by removing it from roller, then lifting tension spring from base. Removed drum to gain full access to motor. Lubricated rollers, vacuumed all areas to remove lint. Replaced motor and belt. Re-installed drum and re-attached tension spring, dryer face, and top. Works fantastic. Hard part was getting spring released and reattached due to location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- evelyn from Brooklyn, NY
- Parts Used:
- WP53-0918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dead Dryer
Vacuum out the dryer vent & trap of all the tenant's sleeping bag stuffing, intall the new lint trap and Voila! It works again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tomasz from Hamtramck, MI
- Parts Used:
- LA-1008
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Loud squeek coming from dryer when running
I took apart the dryer by unscrewing the top and the front, front comes off by just undoing the two top screws on the inside. I figured it was something to do with the rollers since the noise was ciclycal. The hardest part was to put the drive belt back on. It helps to have a second person for about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Brick, NJ
- Parts Used:
- LA-1053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer would not turn on
Lifted top from dryer and fuses were in the back of drum just below heating coil. Used nut driver to remove heating coil to gain access to fuses and replaced them. Process was quick and easy. Diagram from this site made locating fuses elementary!
P.S. I have no certified experience in appliance repair.This was my first time ever and dryer works perfect.
P.S. I have no certified experience in appliance repair.This was my first time ever and dryer works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Gettysburg, PA
- Parts Used:
- WP53-0918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
noise, shaking, from foreign object in the blower, from operating without the lint filter
Lint filter replacement is routine maintenance. operating without a filter causes problems, a dryer sheet was sucked thru the opening and into the blower wheel, causing a lot of noise, and shaking because of the unbalance. I popped the top of the machine up, removed two screw holding the front in place, removed the front, gaining access to blower.
Removed the offending sheet, straighted the bent fin, and put everything back together again. Installeed the new filter, now it runs smooth, and quiet. mission accomplished.
Removed the offending sheet, straighted the bent fin, and put everything back together again. Installeed the new filter, now it runs smooth, and quiet. mission accomplished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JANETTE from MIDDLESBORO, KY
- Parts Used:
- WP53-0918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The lint filter was broken in half
I ordered this part to replace broken lint filter. Shipping estimate was 3-5 working days. I had the part 2 days after I ordered it!! I was very surprised and extremely pleased. If I need anymore appliance parts, I know exactly where to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Brookville, PA
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dryer produced no heat
Checked the voltage to the high limit switch. Found that the element was bad. Ordered the part from partselect.com. and received the part in two days. Unplugged the unit, pulled the lid on the dryer, used the 5/16" nutdriver, removed 3 or 4 screws, pulled out the old and installed the new. Saved a $100.00 service call from the repair man! Novice in home improvement can do this. Thank you Partselect!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from Somersworth, NH
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench set
replace door closer
Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from ANSONIA, CT
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The female catch in door was bro9ken
I took out the old worn out part and replaced with the one I order.
Was this instruction helpful to you?
Thank you for voting!