7430A REV C Norge Dryer - Instructions

I ordered this part to replace broken lint filter. Shipping estimate was 3-5 working days. I had the part 2 days after I ordered it!! I was very surprised and extremely pleased. If I need anymore appliance parts, I know exactly where to go!

Lint filter replacement is routine maintenance. operating without a filter causes problems, a dryer sheet was sucked thru the opening and into the blower wheel, causing a lot of noise, and shaking because of the unbalance. I popped the top of the machine up, removed two screw holding the front in place, removed the front, gaining access to blower.
Removed the offending sheet, straighted the bent fin, and put everything back together again. Installeed the new filter, now it runs smooth, and quiet. mission accomplished.

Checked the voltage to the high limit switch. Found that the element was bad. Ordered the part from partselect.com. and received the part in two days. Unplugged the unit, pulled the lid on the dryer, used the 5/16" nutdriver, removed 3 or 4 screws, pulled out the old and installed the new. Saved a $100.00 service call from the repair man! Novice in home improvement can do this. Thank you Partselect!!!

I yanked up the front of the lid, the broken belt laid across the drum like a dead snake. Pulled that out, then removed the two screws holding the front. Using the pliers, pulled off the two wires snapped to the door switch.
Lifted out the front panel, and lifted the drum, (added a bit of a yank to get it out of the two rollers in the back).
Vacuumed out the dust and dead bugs, then tried to figure out how to thread the belt on the idler and motor. (This was the hardest part) the picture that shows the parts is an exploded view, and does not show the way that it goes together. After about half an hour, I asked for help, and we found a slight rubbing on the idler and figured out that the tensioning spring pulls on the lower part of the idler arm, not the top. Putting the belt on, and getting the spring into the hole in the base was tricky, but not hard. Reassembly was straightforward, and took less than 5 minutes. (put in the drum with the belt on it, hook the belt on the motor and idler, push the rear of the drum into the rollers, then put on the front panel, re-attach the door switch, and the two screws holding the front, and close the lid).

Worked with a guy, I'm a girl. He had a good "feeling" about how to take apart the dryer, install the belt and put it back together. After one go putting the belt on, starting the dryer and having the belt come off....I followed along silently looking at the directions. Definately needed 4 hands to put the drum back in alignment. Other than that, this was very simple PROVIDED THE DIRECTIONS TO REALIGN THE DRUM are followed at the end. So simply: my directions are meaningless here, just follow the ones enclosed with the belt and this should take no more than 1 hour. :)

Took the top off then front off of the dryer with just 2 screws( thank god not the back) and replaced the belt...had a difficult time getting the tension pully in place, belt kept falling off..the stop screw for the tension pulley was bent ,so had to replace that first.

Dont go in through the back!! Take the top off then the obvious steps to get to the drum and belt. On the kitchen aid model at least I would advise to make all the hassel of replacing the belt well worth your time to go ahead and buy a new tension pulley with the wheel on it as opposed to the all metal tension pulley. My dryer is much more quiet now and seems to be more efficient.

I waited a two days to get my belt then deciced to get a new tension pulley. Ordered it one day and the next it was at my door. This was well worth my time and effort. Thanks PartSelect!!

Pry up front of top and lay back. Remove two 1/4" srews at top corners. The front of dryer will then swing to the right. The drumb will lift out easily. Remove broken belt. Inspect the drum rollers on the back wall. Replace if loose or not turning. Mine needed replacement. The assembly part is not easy. You need the drum in place and after it is in place you can't get the belt on. After 8 tries I got smart and made a prop to hold the idler pully up, then put the belt in place and let the pully down slowly. It worked! Put the front back on and the 2 screws and pop the top back down. Also it is a good idea to unplug the electric cord and turn off the gas (if app).

After removing the control panel face plate, the lid, the front panel, and the drum, I had to trouble shoot the wiring to determine the dead spot. I found it to be the thermal fuse for the heating element. I then unplugged the wires to the fuse, removed the fuse from the fuse bracket, and then replaced evrything in reverse order.

Unfortunately, due to a catalogue glitch, the part delivered was the wrong size. However, Donald of customer service took the time to run down the correct part, and that is enroute to me now. Donald, thank you so much for your help!

followed video except for the second fuse deeper down it was easier to take a piece of string and loop it around the top of the holder so it would not rotate toward the bottom due to the size of the hole for the fuse. hold string loop until bottom of bracket is in place and press top into place as you remove looped string...

Belt was broken Removed the front (very easy) removed the drum. Noticed the roller was damaged. Replaced the roller. Installing the belt was tricky but followed an on line video. This dryer has the motor and tensioner behind the blower housing. There was not enough room to use both hands effectively. So first I placed the belt on the motor then pulled the tensioner until I could slide the belt on the tensioner with my other hand. This was the reverse order from the video. The dryer now seems to be quieter.

Followed the instructions and the repair went like clockwork, took less than an hour. I spent more time brushing and vacuuming old lint from the innards of the machine than I did doing the actual repair. Finished up $0.78 richer, too, from the change I found inside the machine.

Was a little hard getting at the idler pulley being it was behind the blower assembly, but it was the only draw back.

Shut off power and gas, unscrewed lint vent, raised top on angle with rope, unscrewed and moved door switch, unscrewed and took off front, put new belt around drum, then raised front end of drum with 4 narrow pieces of 1" foam insulation which let me view and install the belt connection to the drive motor shaft, adjusted the level of the drum using the rope holding up the top, removed foam pieces, replaced and rescrewed the front to fit the drum front channel, replaced the door switch, replaced the top and screwed it to the lint vent, returned gas and power, and ran confirmation test.