7435A REV F Norge Dryer - Instructions

I first made sure there was power to dryer. It was ok so I unpluged the dryer from the socket and afer researching on line I was sure it was the thermal fuse. I check continuity on the fuse and it did not have continuity. So I installed a new fuse and high temp thermostat (they come together)
Just lift top of dryer up and back. In the left rear corner is the heating element. On top of the element is the thermostat. On the right side is the fuse it is a round disc with two white wires attached. The thermostat and heating element need to be removed to install fuse (one screw each and lift out of the way ) . Need to check for blocked lint or like I had the white plastic hose had a kink and need replaced with metal lint hose.

Had a problem holding drum in place and putting front back on. Got it together and drum wouldn't turn. Had to tear it a part again and belt had turned.

Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time) and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.

Replaced the thermal shut off and the thermistor located on the heating element bracket.
Easy to diagnose and to replace- not totally accessable but not that bad either. Cleaned out lint obstruction causing the problem.

After reading everyone else's comments I started by pulling out the dryer, unplugging the power and exhaust. Next moved the dryer to an area where I had room to lay it on the back. Then using a flat blade screw driver, I popped the top attached tape to the top so I could lean back the top without having to hold it. Removed the two screws from the front panel and removed the door safety shut off before removed the front panel. Then I layed the dryer on its back. Then reached under the drum, pushed the belt tensioner toward the motor puller to release the tension on the belt. Then slid the belt to the base. Pulled the drum up and out of the cabinet. Next I cleaned all the lint and crud out of the dryer components. To remove the clips that hold the rollers in place, I use 2 small flat blade screw drivers. These are inserted at the back side of the horse show shaped clip between the shaft and the clip. When the two screw drivers are rotated like turning a screw they slide the clip out. Next I used a socket wrench with a #8 metric socket(I didn't have the sae size) and removed the screws holding the drum roller brackets. I simply reversed the procedure to install the new rollers. Since the dryer was on its back, when I put the drum back in, its own weight slipped it in place. Then pulled the belt around the drum and between the motor pulley and the belt tensioner. Holding the belt with one hand, I used the other hand to pushed the belt tensioner in and positioned the belt. Then I stood the unit back upright and put the front cover on, replaced the door safety switch, removing the tape holding the lid and then cloed the lid. Of course I put the dryer back in place, leveled it, and it now runs like brand new. My thanks to every one else who gave me hints that saved be about $450!

first I went online and took a look at the schematic and realized that two items can shut the complete unit down and would be easy to check. First I checked the door switch with a multimeter then the high limit non-resettable thermostat. The contacts on the thermostat were open which told me it was bad. Went online to www.partselect.com and found the part really easily. came in when they said it would and it was a perfect match to the original (part numbers on the side and eveything). Make sure you correct the problem that caused the unit to overheat in the first place. IN my case the dryer air passages were full of lint. After a good cleaning put it all back together and it worked better than it has in years.

Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. Put new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......

Open the top of the dryer, thermostat can be plainly seen. this one was obviously fried, made it easy to determine cause of problem. remove old thermostat, pins pull off posts, using socket take off nuts (hang on to the nuts), put the new on. Fixed.

I watched the video tape

Others have shared as well as I can

Vacuum out the dryer vent & trap of all the tenant's sleeping bag stuffing, intall the new lint trap and Voila! It works again.

I just removed 1 screw that held the safety thermostat in and replaced it. Then I removed the long screw that holds the heating element and the high limit fuse in place. Replaced the fuse, cleaned out the lint duct area. Closed the dryer lid and pluged it in, it worked fine.

Lifted top from dryer and fuses were in the back of drum just below heating coil. Used nut driver to remove heating coil to gain access to fuses and replaced them. Process was quick and easy. Diagram from this site made locating fuses elementary!

P.S. I have no certified experience in appliance repair.This was my first time ever and dryer works perfect.

Pulled the old seal off then pushed the new one in place.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!