7435A REV A Norge Dryer - Instructions

Pulled the old seal off then pushed the new one in place.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

I took out the old worn out part and replaced with the one I order.

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

Lint filter replacement is routine maintenance. operating without a filter causes problems, a dryer sheet was sucked thru the opening and into the blower wheel, causing a lot of noise, and shaking because of the unbalance. I popped the top of the machine up, removed two screw holding the front in place, removed the front, gaining access to blower.
Removed the offending sheet, straighted the bent fin, and put everything back together again. Installeed the new filter, now it runs smooth, and quiet. mission accomplished.

Checked the voltage to the high limit switch. Found that the element was bad. Ordered the part from partselect.com. and received the part in two days. Unplugged the unit, pulled the lid on the dryer, used the 5/16" nutdriver, removed 3 or 4 screws, pulled out the old and installed the new. Saved a $100.00 service call from the repair man! Novice in home improvement can do this. Thank you Partselect!!!

I ordered this part to replace broken lint filter. Shipping estimate was 3-5 working days. I had the part 2 days after I ordered it!! I was very surprised and extremely pleased. If I need anymore appliance parts, I know exactly where to go!

followed video except for the second fuse deeper down it was easier to take a piece of string and loop it around the top of the holder so it would not rotate toward the bottom due to the size of the hole for the fuse. hold string loop until bottom of bracket is in place and press top into place as you remove looped string...

Followed instructions for testing, starting with door switch, then push to start switch, then thermal fuse. Thermal fuse was bad. Replaced thermal fuse. Back in business.

First thing was to disconnect power to the dryer. I lifted the top lid and found 1 screw on each side at the top near the front and removed them. I also removed the door switch (CLIPPED ON) leaving the wires connected to the actual switch. Then the front panel lifts up and outward. I was able to install the belt from the front, guiding it back to the pulley/idler arm. Reassembled and it worked great. The belt I bought from this site appears to be better than original stock. It should last a long time. :)

I watched an online video about how to replace a dryer belt & followed the directions. Placing the belt around the drum is easy but stringing it thru the pulley is a little difficult because the belt has tension. This takes a little effort but is doable. Dryer runs great now........Be sure to unplug appliance 1st........

Pretty much just followed the video - I'd never opened a dryer before, so I'd watch a step, pause and do it, then run the video a few more minutes, and repeat. These dryers are really extremely simple devices: just a heater, then a motor to spin the drum and run the fan (I think the same motor does both). So you loosen a couple of screws, pry the metal case open, and slip on the new belt. Done! I didn't keep track of time, but I'm psyched to have saved myself a $200 repair call! Standard delivery arrived in less than two days, just like they said it would.

Unfortunately, due to a catalogue glitch, the part delivered was the wrong size. However, Donald of customer service took the time to run down the correct part, and that is enroute to me now. Donald, thank you so much for your help!

Just as described in the installation video provided by Partselect. I replaced the Thermal Fuse and the High Limit Thermostat. The most time was spent replacing the fuse due to it's location.