HDE2000KW Maytag Dryer - Instructions

Finally got tired to greasing the wheels only to have to do it again so I sprung for new wheels and shafts. Popped the top open, removed the drum, installed the two new shafts with supplied screws then attached the wheels. Figured I'd change out the original belt while I was at it even though the old one still looked good. It's nice and quiet again, plus it give me a chance to clean it out.

Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

googled"dryer not heating". landed on partsselect.com. checked parts like website said with multimeter. pointed to thermostat. ordered it, replaced it, it works now.

My part came a day or so after the order was placed. There was really no installation required, but I will definitly make orders from this site again. Thank you very much!

After reading everyone else's comments I started by pulling out the dryer, unplugging the power and exhaust. Next moved the dryer to an area where I had room to lay it on the back. Then using a flat blade screw driver, I popped the top attached tape to the top so I could lean back the top without having to hold it. Removed the two screws from the front panel and removed the door safety shut off before removed the front panel. Then I layed the dryer on its back. Then reached under the drum, pushed the belt tensioner toward the motor puller to release the tension on the belt. Then slid the belt to the base. Pulled the drum up and out of the cabinet. Next I cleaned all the lint and crud out of the dryer components. To remove the clips that hold the rollers in place, I use 2 small flat blade screw drivers. These are inserted at the back side of the horse show shaped clip between the shaft and the clip. When the two screw drivers are rotated like turning a screw they slide the clip out. Next I used a socket wrench with a #8 metric socket(I didn't have the sae size) and removed the screws holding the drum roller brackets. I simply reversed the procedure to install the new rollers. Since the dryer was on its back, when I put the drum back in, its own weight slipped it in place. Then pulled the belt around the drum and between the motor pulley and the belt tensioner. Holding the belt with one hand, I used the other hand to pushed the belt tensioner in and positioned the belt. Then I stood the unit back upright and put the front cover on, replaced the door safety switch, removing the tape holding the lid and then cloed the lid. Of course I put the dryer back in place, leveled it, and it now runs like brand new. My thanks to every one else who gave me hints that saved be about $450!

Had a problem holding drum in place and putting front back on. Got it together and drum wouldn't turn. Had to tear it a part again and belt had turned.

Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time) and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.

It was easy. Just removed the old seal and plugged the new one in place. Took less than 3 minutes

watched your video on 'how to' and did it like man showed..no problem

First I removed the screws of the dryer cover. Next removed the screws holding the dryer drum.

Drilled out the two rivets left from the old glide. Inserted the plastic and postitioned the cushion underneath. Inserted the new glide and drilled a hole in the plastic to accomodate the new rivet. Inserted rivet. Pulled the other end so it was tight holding the cushion and did the other end. Done.

Had to cut the glide 1/4 '' of the width to slide it through the existing slots in the panel.

1.Removed retaining clips,washers,spacer,and cylinder rollers
2.Removed and replaced support assembly
3.Installed spacer
4.Installed cylinder roller assembly
5.Installed washers and retaining clips
This is my second time ordering parts from PartSelect and I am amazed how fast I recieve my orders, which minimizes the downtime of an appliance that's frequently used.

Lifted the top, then removed two screws holding on front panel, then removed cover holding this part in place, then used retaing ring plyers to remove the ring, then plyers to remove wheel clamp, took off the blower wheel. After that did everything in reverse to put it back together. And now the dryer is quite.

Easy repair and I am not the handyman type. Unplug the unit. Lift the top. Remove 2 wires from temperature sensor and remove single screw to lift out the plate the sensor is mounted to(Easier to change the sensor out this way). Remove 2 wires from heating element and then remove single screw. Lift out heating element and replace with new one. Screw back in and reattach 2 wires. Remove 2 screws on the plate for the temeperature sensor and replace with the new sensor. Once 2 screws are back in the plate holding the sensor, screw back in with single screw and attach 2 wires. I called a tech and they wanted $125 just to look at the unit. When I read other reviews of how easy this repair was, I thought it was worth a try. Definitely saved us a bunch of money and time.

Received the replacement filter which was an exact duplicate of the 22 year old filter. Took the old one out; slid the new one in and got ready for another 22 years of use. At 86 years of age I probably won't be around to see the new filter wear out. The dryer has already outlasted the place where I purchased it - Montgomery Wards! They just don't make stuff to last like this anymore.