SDE4000AYW Maytag Dryer - Instructions

There was no repair, just replacing the old, wornout lint filter. But I wanted to thank you for the ease in finding the part and for your prompt delivery. I really appreciate that. If we need any other parts we will order them from you.
Thanks again!

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

I watched the repair video and followed the instruction given to replace the belt. The instructions were easy to follow and to the point. The one thing that was not covered was to vacuum the interior prior to closing the dryer up.

All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.

Replaced the two drum rollers and the tensioning arm roller. NOTES: 1. There are two drum rollers, the diagram seems to show only one. Recommend replacing both drum rollers and the support bracket shaft assemblies since the shafts might be scored. 2. The tensioning arm roller was actually much worse and frozen, so once you are in it is best to replace ALL three rollers. 3. I also replaced the belt since it was worse for wear from the frozen rollers. 4. The PartSelect video for the procedure is for the Whirlpool branded version of this dryer. The internal parts and construction are identical, however, the initial steps for opening up the dryer are different. On the Amana the top also tilts up, but is held down by two bolts, and not just the spring clips. Steps are: a) Remove bottom kick plate which is held in by two bolts on the lower front edge. b) remove the retention bolts that are now exposed on the front panel and remove the front panel by pulling it down from the top spring clips. c) Unbolt and remove the front drum retention panel. d) The two bolts that hold down the top can now be removed and the top panel tilted up so the drum can be lifted out after the belt is loosened. The whole process is very quick and easy. Only tricky part is fumbling around behind the motor to move the tensioning roller and arm to remove and re-install the belt. Also, I had cheap spring clip pliers so I was fumbling with the spring clips that hold the rollers on their shafts.

watched video for Each Part

Using instructions from your website, I was able to remove access covers from my driver & find the pieces that needed to be replaced. It was a simple repair job & now my dryer is working properly again.

After taken apart to replace high limit thermostat fuse and limit thermostat took about 5 minutes. Also our dryer always ran very hot no matter what setting it was on. Replaced idler pulley wheel also because seemed not to rotate very well. Put all back together and worked perfect. Ran and does not overheat now.

Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!

Removed the lower front cover. Unplugged two wires and removed two screws in element, slid element out, removed two contacts and attached them to th new element, slid element back in place, inserted two screws re-attached two wires.
Very easy!

I asked the Gas Co. if they can come out and relight the pilot to my dryer... (which is common for gas dryers) He tested the equipment and told me that the thermostat was the problem. Most places was looking for around $160 for parts and labor. Well, I saved around 130, as I just simply replaced the thermostat. DONE DEAL!

I took out 6 screws and replaced the heating element, changed wires and reinstalled

took one out - put new one in

Once I was able to take apart the door assembly, I was able to determine that I needed the lint duct assembly. The parts website was very helpful with diagrams and explanations so that I could order the part with confidence. Since laundry is so important in our house I paid for expedited shipping. The part arrived in Florida less than 24 hours after it was ordered and soon after it was installed and the dryer was working properly.

Jumped out both limits and flame would still go out, grab the 2 plug gas valve solenoid and it would click and the flame glow coil would start back up. I ordered both solenoid valves and the flame would stay on longer but not like it used to. On time drying the flame should stay on all the way thru the cycle unless it got to hot and the cycling stat would take over. Ordered a cycling stat and now it heats like it used to. The clothes are hot now when they come out. If you jump out the limits and still the flame doesn't stay on like it used to, replace the gas valve solenoids and the cycling stat.