YNED5800DW0 Maytag Dryer - Instructions

I saw a couple of videos to replace this but found a simpler way to replace the heating element on my dryer. DISCONNECT the POWER.
I removed the lower panel (6 screws). Dis-connected two wires; one going to the heat sensor in the back and the other to the switch at the front. Removed the two screws to the metal plate in front of the heating element. Slid the whole heating assembly out. Removed the screws holding the heating element in the housing. Removed the failed (open) heating element and installed the new one. Reversed the process for re-assembly.

Took door off with a Phillips screwdriver went to hardware store with door so he could match up the 6pt screwdrivers that were needed.
No more then 1 hour to do.

Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding each one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.

I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.

Remove top, remove two front panels, remove rear panel to access drive motor release tensioner. Remove drum to access to heating element enclosure. Replace and reinstall after vacuuming all accumulated lent.

You tube

Pretty easy repair and I am not very handy. I believe they engineer these machines so you hire someone to do the job. They could place that part in an area where it is easier to get to, like a door on the side or something

It was a lot easier then I thought. Just watch the tutorial of how to fix it on this website and you wont have a problem.

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

I followed the video instructions. I took my time as this was a first for me. The disassembly was fairly straightforward. The belt idler pulley was definitely the problem as it wouldn’t turn at all. I decided to replace the support rollers also even though they seemed to be ok. Everything I had read said my model only needed 4 rollers but actually needed 6. I had to place a second order for those. Putting it all back together was fairly easy. Overall I had a good experience. Only a few tools were needed for this repair. Thank you,

I removed the top first followed along with removing the side bracket that holds the circuit board. I then proceeded with removing the bottom cover and front panel. I disconnected the front panel from the control board and was able to slide the front panel upward. The door and blower housing was a bit tricky to pull out without thinking I was damaging something. I then replaced all the seals and cleaned the dryer after removing the drum and belt. I also replaced the drum support rollers. Afterwards I put everything back together and had an "E1" error and I pulled the thermostat out and wiped it down from all the lint and dryer worked perfect after that. Dryer takes the right amount of time to day clothes and no more rumbling noise. The instructions videos were VERY helpful.

Use the adjustable wrench to remove the water line. Remove the dryer vent line. Take off the screws on the main back panel, the screws connecting the top. Place both off the side. Unscrew and remove the parts connecting to the heat line located on the left side. Remove the front unit screw attaching the heat line to the bottom of the dryer. Remove the four screws connecting the top and bottom of the heat line together. The two on the left side is a huge pain, make sure you have small hands to be able to reach on the side of the line. Pull the bottom of the heat line loose. The heating element is inside the line. Replace element and put everything back in the order it was removed.

Followed your video for replacing the Tension Pulley, Drum Belt and Drum Rollers. Models were not exact, but instructions were very clear and detailed enough for a "computer geek" to do the repair myself (with some help from my wonderful wife). Live in Ohio, parts came from Kentucky and I had them the next day! The dryer is almost 10 years old. Running great now. Thank You!