YMEDB880BW0 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ERNST from FLOSSMOOR, IL
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
broken door catch
pushed the broken catch into the door and snapped the new one back in. Works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henri from SILER CITY, NC
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Plastic part in door catch was broken so door would not lock to allow the dryer to operate
I tried to remove the part with pliers but could not remove it so I removed the screws that hold the front part of the door. I took the front part off, removed the broken plastic and then lifted on side of the catch so that the bottom of the front part came thru the door and then was able to remove the door latch. The installation of the new part took about 15 seconds to put in by pushing it into the opening where the broken part was removed. I put the front part of the door back and put the screws back and the dryer works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from ALBANY, OR
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lint screen tore and had a side that was loose so it didn't catch all the lint and cut your fingers
Removed the old screen and simply put in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LANA from INDIANAPOLIS, IN
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Door would not clisr
Had to force the old door catch out using the putty knife didn't work. Worked on it until I finally forced it out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from MARIETTA, OH
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer Drum Would Not Rotate
Followed your video for replacing the Tension Pulley, Drum Belt and Drum Rollers. Models were not exact, but instructions were very clear and detailed enough for a "computer geek" to do the repair myself (with some help from my wonderful wife). Live in Ohio, parts came from Kentucky and I had them the next day! The dryer is almost 10 years old. Running great now. Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fabiola from CANYON CNTRY, CA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Very satisfied with the lint filter and with fast shipping, thank you!
Easy manually
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from S GLASTONBURY, CT
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace lint filter
Just insert filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from OXNARD, CA
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint passing old screen.
Exchanged old for new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tiffaney from QUAKER CITY, OH
- Parts Used:
- 4392067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Belt pulley bad.
Followed the instructions on your video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Blue Ridge, GA
- Parts Used:
- WP8544742
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
belt broke
had no room to work in the back of the dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Twinsburg, AL
- Parts Used:
- W10854425
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken clips
Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from HOUSTON, TX
- Parts Used:
- W11226088
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer lens had melted
i removed the old lens,then removed the bulb,after ordering and receiving your replacement lense,it went back on just like the old one.the repair was very easy. thank you. D.S P.S1 IAM A REPIARMAN NOW!!! WITH YOUR VIRTUAL REPAIRMAN APP,VERY VERY SMART ILL SPREAD THE WORD.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from Wausau, WI
- Parts Used:
- WP8577274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Gas dryer shut off mid cycle in timed cycle mode
Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!