YMEDB800VU0 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from BENTONVILLE, AR
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
door would not latch
removed old latch with pliers - inserted new latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gabe from Tulsa, OK
- Parts Used:
- WP8544742
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Blower belt came loose, but didn't snap. It was old and perhaps brittle.
First, lift top by pushing in the 2 locking clips ( with the dryer door open), otherwise it won't lift.
Secondly, remove front cover by taking out 2 screws easily seen . If you see any electrical connectors, remove them.
Only thing a bit nightmarish was installing the new belt. It didn't seem long enough even though it was the original exact replacement. I got hair dryer blower, used on belt for 30 seconds, and mission accomplished.
Secondly, remove front cover by taking out 2 screws easily seen . If you see any electrical connectors, remove them.
Only thing a bit nightmarish was installing the new belt. It didn't seem long enough even though it was the original exact replacement. I got hair dryer blower, used on belt for 30 seconds, and mission accomplished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BOILING SPGS, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
My dryer was squeaking with an occasional thump
Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from STONE CREEK, OH
- Parts Used:
- WPW10314173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dryer drum turned hard because rollers were worn
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from HUNTSVILLE, AL
- Parts Used:
- 4392067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Sqeeking noise fron old worn belt and rollers
Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.
Was this instruction helpful to you?
Thank you for voting!
Tub seals were out , major clean up!..
Tear down , pulled drum, rollers, belts. These machines are very simple and very reliable!. I love these machines, they are one of the easiest to work on of any machine l have worked on. I have been a mechanic all my life!.Maytag got it right , their washers are as easy to work on as their dryers!..Very, Very simple..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from COCOA, FL
- Parts Used:
- WPW10314173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Roller Berings were worn out - replaced both
Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TULELAKE, CA
- Parts Used:
- WPW10314173
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
dryer making noise. order parts
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from HUNTINGDON VY, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad screaming noise
Replaced 4 wheels and new belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Annapolis, MD
- Parts Used:
- WP3387223
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Clothes were not drying on auto sensor.
Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from Bainbridge, PA
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Dryer would shut off mid way through cycle and give an E1 error code
After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from Vernal, UT
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A hole in filter
Remove old filter
Vacuum out
Install new filter
Vacuum out
Install new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Oceanside, CA
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door Latch Broken
Ordered new latch. Installed new latch into the dryer within one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Colorado Springs, CO
- Parts Used:
- WP3387223
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
not drying completely on the automatic settings
Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from MARION, KY
- Parts Used:
- WPW10314173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Making a racket.
Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.
Was this instruction helpful to you?
Thank you for voting!