YMEDB400VQ1 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Annie from HENDERSON, NV
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The door catch on our Whirlpool Dryer had given out.
The repair cost us less than $9.00 and about 1 minute to repair. You can only imagine how much a tech would have charged us!! We are so very happy that we discovered this site . The instruction video they offered, the customer service via their website AND quick delivery of the part, has insured them that we will be repeat customers. Thanks so much !!!!! Bravo! Annie & Peter in , Nevada
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SCOTTSDALE, AZ
- Parts Used:
- W10120998
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Torn filter seal
Remove old filter, throw it away, replace with new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DW from ALVIN, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
F-26 Fault message
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
Thank You.
DW Pranger
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fabiola from CANYON CNTRY, CA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Very satisfied with the lint filter and with fast shipping, thank you!
Easy manually
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from MARIETTA, OH
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer Drum Would Not Rotate
Followed your video for replacing the Tension Pulley, Drum Belt and Drum Rollers. Models were not exact, but instructions were very clear and detailed enough for a "computer geek" to do the repair myself (with some help from my wonderful wife). Live in Ohio, parts came from Kentucky and I had them the next day! The dryer is almost 10 years old. Running great now. Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from S GLASTONBURY, CT
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace lint filter
Just insert filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tiffaney from QUAKER CITY, OH
- Parts Used:
- 4392067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Belt pulley bad.
Followed the instructions on your video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Blue Ridge, GA
- Parts Used:
- WP8544742
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
belt broke
had no room to work in the back of the dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from OXNARD, CA
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint passing old screen.
Exchanged old for new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Twinsburg, AL
- Parts Used:
- W10854425
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken clips
Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from HOUSTON, TX
- Parts Used:
- W11226088
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer lens had melted
i removed the old lens,then removed the bulb,after ordering and receiving your replacement lense,it went back on just like the old one.the repair was very easy. thank you. D.S P.S1 IAM A REPIARMAN NOW!!! WITH YOUR VIRTUAL REPAIRMAN APP,VERY VERY SMART ILL SPREAD THE WORD.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from Wausau, WI
- Parts Used:
- WP8577274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Gas dryer shut off mid cycle in timed cycle mode
Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julian from San Antonio, TX
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Noisy/Rattleing Tumbler
First i did some research on the internet approx.1yr ago.Just in case any problems like this or any other kind of problems should arise which it did.The whole thing is Easy all you have to have is some basic knoledge of how things work.All of this came "OFF" in (4) sections.After installing everything back it was as "Quiet"as the day we purchased it.Good for another 5yrs.Retired welder & "J.O.A.T.Julian San Antonio,Texas
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Sussex, WI
- Parts Used:
- WP3387223
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Suspected bad moisture sensors
Opened machine up, removed electric control panel, removed door assembly, removed lint collector assembly, removed and replaced 2 sensor bars then reassembled machine. Ended up not being the problem but, I now have new moisture sensing bars.
Was this instruction helpful to you?
Thank you for voting!