YMEDB980BG0 Maytag Dryer - Instructions

removed old latch with pliers - inserted new latch

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

Tear down , pulled drum, rollers, belts. These machines are very simple and very reliable!. I love these machines, they are one of the easiest to work on of any machine l have worked on. I have been a mechanic all my life!.Maytag got it right , their washers are as easy to work on as their dryers!..Very, Very simple..

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.

I expected to find a broken blower belt so purchased that belt and the others I planned to replace since the on line instructions indicated that I had to pull the drum to replace the blower belt. I did not, so didn't use most of the parts at all. The instructions that came with the parts, were only slightly helpful because they were for a far different model. Some youtube videos were more help. I had to pop the top, which is easy and explained in the instructions, remove the front panel, which only requires removing two 5/16" small bolts, then lifting it up and off. Simple. With that panel off, I could see the blower belt and it was intact and seemed to work fine. I could have replaced it easily with no further disassembly at that point. However, since it was not blowing the air out of the dryer, I knew there was another problem. So I removed the front of the blower housing, which is four, 1/4" small bolts and it just pulls off. I could then see that the entire front of the blower was packed with lint that had gotten past the normal lint filter. I cleared that all out and checked that the blower itself was intact and clean and there were no other obstructions. When I rotated the blower by turning the motor, it moved easily. So I put it all back together without changing any parts and tested it. It worked perfectly again. I kept the parts for the next time I might need them.

I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.

sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.

I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.

Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)

Replaced 4 wheels and new belt

Ordered new latch. Installed new latch into the dryer within one minute.

turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.

Removed the old hoses and screwed on the new hoses.

Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.

Ezee pezee lemon squeezee.