YMED8000AG0 Maytag Dryer - Instructions

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

replaced heating element

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

Unplug unit first.
Took the front cover off the front of dryer below the door.

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.

Since it was a dryer filter, it just had to be put in the dryer. Works GREAT!!

Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.

My dryer would not start or turn. I first moved the timer to midway between start and end of a cycle and could hear the timer ticking, likely eliminating the timer as the culprit. I next opened the door, manually pressed the door-closure switch and pressed START to see if the heating coil was heating without the drum turning to see if it might be a motor issue. After no heat, I unplugged the dryer and removed the vent hose by loosening the clamp and then removed the lower back cover using a socket and ratchet. Using a multimeter, I quickly found an open thermal fuse. I tested the remaining components to see if they also required replacement (coil, thermostat, high temp sensor) - all tested good. Took a chance and ordered the fuse alone instead of also purchasing replacement thermostat as many advise - if you have not replaced in a while, probably worth doing now. I have replaced mine within a year or two and chalked up the issue to my kids not clearing the vent, so I went without the new thermostat. Model number was found by opening the lid - parts arrived incredibly fast especially for being around the holidays. Replaced the fuse with ease - there is a notch in one end that holds the non-screw end in place so it's flush. Plugged the dryer back in, selected a cycle and confirmed the dryer started and heated as normal. I then had my son open the dryer door to confirm the drum stopped turning. HERE'S WHERE IT TAKES A TWIST: When the door was open, the heating coil continued to glow red hot (faulty timer??) I moved selector to end of cycle and the glow stopped. (timer's good) I then moved the selector mid-way between cycles with the dryer door open and WITHOUT PRESSING START and the coil again glowed red. Disconnected power, disconnected coil and using multimeter, checked from coil input to case ground (any bare metal) and found one side of the coil to be grounded. I was able to removed the heating coil and locate where the coil was touching the case. I shifted the coil back into place, checked with meter (no ground this time), reinstalled and tested with no problems. Reinstalled the back plate and vent hose. Finally, had conversation with the kiddos about being gentle when moving the dryer and all was well. The thermal fuse portion took 15 minutes from diagnosis to replacement. The overall process (due to the additional grounded heating coil) took 30-60. With any repair like this, I usually recommend visually verifying the heat cycles on and off by carefully running with the door open and holding the switch. This will help you determine if you may have an additional faulty part that made the first one fail. (Most likely, thermostat).

Removed Back and found schematic. Found fuses on schamatic and parts inside dryer. Checked fuses and thermal fuses with an ohm meter and found one that was open. Went to Parts select and ordered part. Relpaced the part and dryer works like new.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Performed current check to determine possible problem-then Able to go on line with partselect, extremely easy part description and selection, ordered, part arrived next day. Could not have went any better

Remove top,front and panels.change thermal fuse and outlet thermistor.