MEDB955FC1 Maytag Dryer - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I highly recommend the videos on this site for repair information. It wasn't exact for the age/model of my dryer but very close. Remove the top panel and then the control panel. Remove the lower front panel and finally the door and main front panel. Unloop the belt from the motor and remove the drum. I found one of the drum rollers was bad, which was causing my problem, but I replace all 4 rollers, the belt, and the idler wheel. Sounds like it did when it was new! Find the video for your model and watch it!!

flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.

Watched a brief video on YouTube and followed step by step. Real easy.

First tried repairing the old idler by cleaning and lubricating the shaft. That lasted for about a week but the squealing returned. Ordered the part and had it in a few days. Replaced the idler wheel and it's been quietly running like new for several weeks now. Now wife thinks I'm Superman.

Disconnected the power and duct from the dryer. Removed the back and top of the dryer by removing the 1/4" screws. Created slack in the belt by compressing the spring and moving the idler arm.Slid the belt off the pulley. Removed the tri-ring clip, slid the old pulley and gasket off. Cleaned and inspected the shaft and vacuumed the inside of the dryer. replaced the gasket, pulley and tri-ring clip. Replaced the top and back of the dryer. Connected duct and power.

Removed the top panel of the dryer via a couple of screws from the rear. Remove the rear panel swing it open light a door to the right, minding the electrical connections. Removed the belt from the pulley, removed the Tri-ring from the shaft and slid the pulley off of the shaft. The shaft was slightly rusted so I used a steel brush and brake cleaner to clean it up, placed the new gasket, pulley, and tri-ring on, replaced the belt, and put the panels back into place. As the dryer is about 7 years old, also removed the front lower panel and cleaned out unit which had quite a bit of accumulated dust and glitter especially in the vent lines. (3 girls live here). Pretty easy, most screws remove with just the one tool.

The repair went great . Thanks for the part ,will be purchasing parts from you now on.

Took the back dryer cover off and removed the lint cover all from the back of the dryer then replaces the Thermistor (held with 2 screws).

We did repair by first watching a you tube video, then jumping in an dgoing step by step through the video. While not exactly the same dryer, the steps were in sequence. We thoroughly sleaned out the dryer with the tub out before reassembly. Th eonly slightly tricky part was putting front piece back, but once we mad esure ot align the sides for squareness the dryer went back together smoothly, execpt for one dropped screw. that was fished out through the bottom panel. The dryer runs quietly and we can watch TV with the door open to the laundry room again. I should have done this a long time ago. It started out by sqeaking at startup, then grew worse over time. I recomend anyone with a friend should be able to do this. Now with Cell phone pictures it is even easier to remember where the screw go.

Thank you for your part service. It saved me about $ 200.00 dollars by Sears not coming out to repair a simple problem.

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

UNPLUG UNIT FIRST!!! Removed back cover. Make sure to note not all screws hold the back cover by closely observing the screw. Take a picture of the belt routing before removing from the idler pulley. Use headlamp or flashlight to light up pulley area. Remove belt from idler pulley by pushing idler assembly towards the right. Use small screwdriver to remove the existing pulley by prying off the existing tri-ring from the back of the pulley. You may have to "feel" the ring since it in facing away from you. Once tri-ring is removed, slide off old pulley and gasket or old second tri-ring. Replace with gasket first, then pulley then tri-ring. Reroute belt. Use picture if needed. Replace back cover.

Remove the back cover from the dryer after unplugging unit from electrical outlet. Remove the belt by moving tension arm. Remove the tension spring (by hand). Remove the idler pulley bracket with a nut driver. Remove the Tri-Star retaining clip with a screw driver. Remove the old idler pulley. Remove old washer... replace with new washer and idler pulley... I could have reused the tri star retaining clip but elected to use new one. Put arm back on, re-hook spring, realign belt, put back cover back on... dry clothes.

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.