MEDB855DC4 Maytag Dryer - Instructions

Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.

removed broken parts & snapped in new catch

I removed the metal piece which held the plastic "catch". There were no screws, squeeze to remove it. Then inserted the plastic part and re-inserted the metal part into the dryer door. Very simple. But even more pleasing was the easy ordering and the quick delivery of the part! Thank you so much!

first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.

Removed front panel located hearter elemement houseing
removed screw securing houseing to dryer chasis, disconected wireing harness- be carefull here there are three lines two for the thermostat and one for the element- you only need to disconect the one nearest the front of the unit, reove the screw holding the element to the houseing it sits in and pull out. instalation is reverse the directions to remove

Pulled the back panel off with nut driver , reached in removed belt from pulley , disconnected the spring , removed the the 1 bolt holding the bracket .
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!

Removed the screws holding the front cover, Removed the screws holing the heating element bracket, pulled the heating element housing out, unplugged element and removed old element. Very easy to install. The exploded pictures on website really help.

First I unpluged the dryer from the electical power. I removed the 2 screws holding the bottom front panel. Then I saved a bit of time and effort. Instead of removing the bracket and pulling the whole unit out, I bent the metal plate in front of the heating element toward me. I unpluged the 2 wires from the plastic casing and removed the screw holding the heating element in place. Next I pulled out the old part and pluged in the new one then connected it in reverse order and bent the plate back up to protect the element. This was a very easy and inexpensive way to fix the dryer like new again. The hardest part was vacuuming and cleaning the bottom of the dryer. There was seven years of lint build up under there.

unplugged the dryer and removed collapsable vent then we laid it on its back. took off the lower front face with a screwdriver ( just inserted in upper margin and it popped off) then removed a couple of screws and put the new element in replaced the screws and we cleaned all the old dust and lint from in the cabinet and replaced the front face. no problems.

Followed your video for replacing the Tension Pulley, Drum Belt and Drum Rollers. Models were not exact, but instructions were very clear and detailed enough for a "computer geek" to do the repair myself (with some help from my wonderful wife). Live in Ohio, parts came from Kentucky and I had them the next day! The dryer is almost 10 years old. Running great now. Thank You!

I actually had a friend's husband do the repair, who is an electrician by trade. He removed the front of the dryer, removed the box that held the element, removed the element, marked the wiring, and then when the part came, he put it back in, and reassembled the dryer.

Suggest you test all suggested parts first with ohm meter to determine cause of failure. Heater element was functioning properly, other parts were required to fix problem.