PDGT910AWW Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Amy from Petaluma, CA
- Parts Used:
- 37001141
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Vent filter was broken, and lots of lint was passing through to vent line
Removed the two nuts at the bottom of the dryer front to be able to move the front piece. Removed three screws holding the vent assembly in place. Removed vent assembly, replaced with new part and replaced screws and nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from hillsborough, NC
- Parts Used:
- WP37001132
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Worn Felt Seal
remove bottom two screws on lower front panel, remove panel. remove two screws on lower portion of door panel, pull bottom panel towards yourself to release pins at the top. Disconnect wiring for light and door switch (make sure to note what wires go where. Complete removal of front door panel. Remove 4 screws holding cylinder frame in place, lift to remove. remove remnants of old felt seal, use rotary tool to remove excess glue, etc. apply glue (used rubberized gorilla super glue), apply felt seal - allow glue to set up. reinstall in reverse direction from removal. Be sure to use glue as there are no clips or other retaining pieces for the new felt and it will not hold in place. overall pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garrett from PHILADELPHIA, PA
- Parts Used:
- WP37001308
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Gas smell
After removing the front panel, the igniter just just snaps into the bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from HOOPA, CA
- Parts Used:
- 56000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Dryer started making a terrible sound, when my son opened up the appliance he found that the Blower wheel was broken and the housing was full of debris.
My son will discribe how he did the repair.
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicky from Browns Mills, NJ
- Parts Used:
- WP37001298, WP37001036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
When the dryer was on it would still tumble, but made an aweful sound
My son n law took the fron off the dryer, whilw I looked on the inertnet to locate whatever part we would find to be in need of. He pulled the front panel off and the drum out to dicover it was the bracket and glide. They were easily replaced by popping the bracket out and snapping th new one in then placing the guide on it proper spot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GILBERT from SAN JOSE, CA
- Parts Used:
- 37001141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Air duct was broken,taking too long to dry
removed the bottom panel. then the door. unscrewed the 4 screws, removed duct and replaced. parts came fast and fit just right! no issues at all! I recomend Parts select as an appliance vendor for parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Melissa, TX
- Parts Used:
- WP37001142
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
top of the lint filter broke off, tearing our clothes.
Ordered the part, you made it so easy. Received it in two days, very fast, by regular mail. Perfect fit. Pulled out the old broken one and put in the new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from sherman, TX
- Parts Used:
- WP37001142
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lint filter
No problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cara from oceanside, AL
- Parts Used:
- WP37001184
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
time broke in half and we've been using a plyers to turn on
It just pushed on and clicked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from Portland, ME
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door would not close
discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from Somersworth, NH
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench set
replace door closer
Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from ANSONIA, CT
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The female catch in door was bro9ken
I took out the old worn out part and replaced with the one I order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Virginia Beach, VA
- Parts Used:
- WP2200376, WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Dryer would start loud humming noise 20-30min into cycle-rear bearing going bad
Unplug Dryer. Remove 2 5/16in hex screws fm lower panel,3 51/6in hex screws to vent duct. Remove 2 1/4in hex screws to thermostat. Remove 7 1/4in hex screws to blower cover and 2 5/16in hex screws holding base footings.Use adj. wrench to hold rear nut on motor shaft, use7/8in socket to remove fan frm motor shaft. Remove 3 5/16in hex screws holding fan housing to motor mount. Lift-up on spring tensioned belt pulley to remove belt. Pull motor & mount out [wires are layed toward front allowing removal]. Use 6in flat tip screwdriver to unsnap both front/rear motor clamps.Pinch plastic end clamps and remove motor electrical connector.Motor installation is reverse. For belt removal,remove 2 5/16in hex screws to door panel [unhook 2 wires to upper RT rear to door switch].Remove 4 5/16in hex screws to front bulkhead panel.Allow drum to sag IN PLACE [removal not required to replace belt],note belt location and slide old belt off and new one on
Replace Bulheald and door panel [re-attach door switch wires].Complete install by lifting belt pulley and feeding new belt into place. Hand rotate drum to ensure proper belt allignment and tracking. Replace lower panel. Vacuum interior as necessary. Parts delivered in 3days and fit perfectly.
Replace Bulheald and door panel [re-attach door switch wires].Complete install by lifting belt pulley and feeding new belt into place. Hand rotate drum to ensure proper belt allignment and tracking. Replace lower panel. Vacuum interior as necessary. Parts delivered in 3days and fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from VALENCIA, CA
- Parts Used:
- 489P3
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Drying time exceeded 1 to 2 hours and lint was damp on lint screen
Removed two screws on lower front dryer panel with 5/16" socket and wrench. Removed three screws and plastic filter dryer screen vent with 1/4" socket allowing easy access to upper limit thermostat switch located on side of igniter flame assembly tunnel. Removed two screws attaching limit switch and disconnected two wires. Replaced with new limit switch and reconnected wires. Reassembled dryer. Works fine. Drying time for regular items such as towels is now less than 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from GRESHAM, OR
- Parts Used:
- WP40111201, WP37001287, WP37001042, WP500121
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench set
Screaching on start-up, then continuous after time
Idler was the noise source. Drum support rollers were failing also. I almost spent $500.00 on a new dryer, glad I replaced the parts instead. Sounds and works like new. Watch the video,its very helpful. Thanks Parts Select. You should advertise your services on TV or radio. I am glad I found you.
Was this instruction helpful to you?
Thank you for voting!