MGDX700XL0 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The sensor would not slide into grill
Initially, i watched the how to do it instruction in the fix website to determine the complexity of repairs. The instruction built up my confidence. I ordered and recieved the grill amd the two new sensors. I placed the two new sensors into the new grill sensor slots. Then removed the old grill by unscrewing three screws. Connected the two sensors positioned the grill and screwed in the three screws put the lent stray in the grill and closed the dyer door. I have been a happy camper ever since. I saved the $75 home insurance fee plus maintenence installment. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracie from Culver City, CA
- Parts Used:
- 279311
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
dryer worked but no heat
Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.
Was this instruction helpful to you?
Thank you for voting!
Replaced two parts in the gas heater assembly
I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with the new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Novi, MI
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heat Would Not Come On
After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.
After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lot of time and money if I had read that earlier.
After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lot of time and money if I had read that earlier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry Duty from Fort Walton Beach, FL
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
idler pully sqwieling
once the back is off remove belt from tentioner and remove v clip. smooth shaft with wd-40 and scotch brite , then install new idler replace v clip
and your done !!!
and your done !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Laredo, TX
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The felt strip on the filter had come undone.
Took the old filter out and inserted the new one- works great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colleen from CAPE CORAL, FL
- Parts Used:
- WP3406107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer continued to run with door open
The video provided by this site on YouTube on this topic was perfect. Saved us a couple of hundred dollars DIY rather than repair man.
Was this instruction helpful to you?
Thank you for voting!
Dryer starts with loud squeak initially. Eventually there was a loud clank and dryer stopped.
Rather than remove the front panels, door, control panel and drum, I noticed 1/4" metal screws on the back panel. There were approximately 6 holding the back panel in place. I did have to remove the top panel as well before removing the back. Once removed I had complete access to the broken idler pulley assembly. I immediately saw the broken pulley. I installed the new one with very little effort. Reset the belt according to instructions from the video. Reassembled, plugged in, hit start and enjoyed the sweet sounds of success. All told it took me about 20 minutes from start to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Midland, TX
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
seal for lint filter came off
Pulled out the old and slid in the new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Jamestown, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door catch on dryer door broke
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might contact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rodney from Mad River, CA
- Parts Used:
- WPW10512946, WPW10359272, WPW10359271, WPW10314173
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
parts took more than two months to get here.
I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim K from Hurst, TX
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dryer would not turn
My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from LONG ISLAND CITY, NY
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Time clock not moving .Not enough heat
Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Duarte, CA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer gasket detached from screen
Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.
Was this instruction helpful to you?
Thank you for voting!