MGDX655DW1 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Long Beach, CA
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
No heat...
Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Canyon Country, CA
- Parts Used:
- 279311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
The dryer would not heat up
After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from VENICE, FL
- Parts Used:
- W10861225
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The dryer door handle broke.
Replaced with new handle in 10 seconds
Was this instruction helpful to you?
Thank you for voting!
dryer would not work .
Took the old parts out and installed the new parts in , everything that you sent fit perfect!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from PORT ST LUCIE, FL
- Parts Used:
- WP3406107
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The dryer wouldn't stop when I opened the door.
I Picked up the two front corners up, after removing the 2 screws from the vent and the 2 screws that hold the door switch in place, then I disconnected the old switch and put in the new one. Just the opposite of how I took it apart. Very simple and it works great!! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from BEVERLY HILLS, FL
- Parts Used:
- WP3406107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer would not start
Part came in about 3 days. After reading and checking what was wrong with the Dryer -- which i read if there was no noise coming from the dryer it was the door switch, Looked up the part number and then saw a video that showed how to install the door switch. The video was so informative and precise on everything you had to do and easy Saved money on a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from SYRACUSE, UT
- Parts Used:
- 279827
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Mother was frozen up
I followed the video. So easy..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Serena from ESSIE, KY
- Parts Used:
- WPW10642928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Timer was not working,
Repair was fairly simple, unplug power from dryer, take back top panel off, remove timer knob, remover timer switch, un-plug one lead at a time, and place on new timer, reconnect timer, put back on back panel, reconnect power to dryer, and that it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- diora from ROCKFORD, IL
- Parts Used:
- W10861521
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
wore out gasket
removed old gasket took door off 4 screws. cleaned seal area applied glue put on gasket easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from N RIDGEVILLE, OH
- Parts Used:
- W10861521
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replace dryer door gasket
Take the door off of the dryer. Lay it on a towel. Remove old gasket. Clean the channel the door gasket fits into with glue remover. Squeeze high temperature glue into the channel, let the glue set up. Put the new gasket into the channel, tape it down in a few places. Let it sit 24 hours for the glue to set up. Put the door back on. You can put the door on immediately as long as you don't use the dryer for 24 hours. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CLIFTON HTS, PA
- Parts Used:
- WP694089
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Motor was bad
I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part so I can redo a testimonial here for you. 19 days and still waiting
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from AUBURNDALE, FL
- Parts Used:
- W10861225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Dryer Handle
Easy, just snapped it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BEDFORD, TX
- Parts Used:
- W10861225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke
Went to the site for instructions. Received a nice set of three photos with detailed instruction. Very easy to follow and item just snapped in. If I hadn't looked up the instructions I would have probably risked breaking the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from STONE CREEK, OH
- Parts Used:
- WPW10314173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dryer drum turned hard because rollers were worn
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from FLINT, MI
- Parts Used:
- WP8318268
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Dryer was not heating
The cycling thermostat was found to be not working when I checked it with a ohm meter. I ordered the part waited and installed it and it work just fine.
Was this instruction helpful to you?
Thank you for voting!