MGDX600XW1 Maytag Dryer - Instructions

Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.

Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.

The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.

Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.

Just like the video, just followed the video
Thanks,

After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

The design of the dryer did not make the conversion easy, I had to disassemble the entire front end, top and remove the drum. The kit included a new spud that's it (22.00?). Anyway the gas valve is convertible from NAT to LP only requires turning a portion of the valve about 25 degrees. I managed with a screwdriver as I could not locate my snap ring pliers(just moved). The directions were spot on, read them through once before you start.

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

Kill power to dryer from breaker box.Remove lint filter & 2 screws. Take a flat head screw driver and place in gap between rash from corner of top panel & front panel of dryer and pry up to raise top panel of dryer & rest against wall the wall on angle do it doesn’t fall back toward you. Unplug wiring harness from dryer switch inside top front corner of dryer with outside of drum exposed when top panel of dryer is raised. Open dryer door and remove screws on each side of dryer switch located at upper inside corner of door opening. Take flat head screwdriver had slide in between connector & wiring harness on dryer. Remove old switch. Reconnect new dryer switch to wiring harness & remount switch to inside of dryer door opening. Lower top panel of dryer & press front corners of top panel to front panel of dryer & clips will be locked in place. Replace screws in dryer filter mounting holes yo top panel & replace dryer filter in place. Turn on power ‘ & check if light is working 1st. Then, turn timer knob clockwise, close door and listen if the drum is turning. Open door to see if drum turns. If both work, the job is complete.

I Picked up the two front corners up, after removing the 2 screws from the vent and the 2 screws that hold the door switch in place, then I disconnected the old switch and put in the new one. Just the opposite of how I took it apart. Very simple and it works great!! Thanks

Ezee pezee lemon squeezee.

Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!