MGDE400XW0 Maytag Dryer - Instructions

Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.

Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.

Just like the video, just followed the video
Thanks,

The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.

Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.

I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.

Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

The design of the dryer did not make the conversion easy, I had to disassemble the entire front end, top and remove the drum. The kit included a new spud that's it (22.00?). Anyway the gas valve is convertible from NAT to LP only requires turning a portion of the valve about 25 degrees. I managed with a screwdriver as I could not locate my snap ring pliers(just moved). The directions were spot on, read them through once before you start.

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

Followed instructions for standard blower wheel replacement and repair kit installation, which were straight forward. The only real issue I ran into was removing the blower wheel, The instructions say to turn it clockwise and remove it, however this wheel had been on there for a long time and it also has a taper shoulder so it was not coming off without a fight which is why the dremel tool is listed. I had to cut the old bower wheel out in pieces so I could remove the electric motor, which was easy. Once out and on the bench and only the metal hub left on the shaft a 7/16" wrench and large vise-grips got it to break loose. The good side of this is it allowed me to blow out any lint that had built up on the motor, like new again.

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

Removed the dryer door, unscrewed lint vent.