MGD9000YW0 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Lake Forest, CA
- Parts Used:
- W10837625
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken Motor Pulley
I am a retired applaince repairman not recommended for amature to repair this model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from Middletown, NY
- Parts Used:
- W10869845
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from East Rochester, NY
- Parts Used:
- 279311
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer wouldn't heat.
I ended up taking the entire dryer apart when I didn't need to, and it turns out it wasn't the Igniter Kit in the first place but the thermal fuse in the back. Was pretty simple to repair in any case however.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from SAN DIEGO, CA
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No heat just tumble
Opened the bottom panel w/ 1/4 nut driver to access the flame sensor and easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Epping, NH
- Parts Used:
- 279311
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer runs but no heat
Viewed online then found part and ordered it in, took front off of dryer and cleaned out the dryer. replaced igniter seemed to work but ended up having to replace thermial fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rick from Burton, MI
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Would not heat clothes dry
unplugged dryer and removed front panel. removed the screw that holds flame sensor and unplugged electrical wires. then replaced with new. Did not solve problem so I ordered the replacement coil kit and installed them using phillips screw driver and this solved problem. Dryer is working fine now. I found this site very helpful and would recommend it to a friend.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David M from Watertown, WI
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer would heat up for a short time, then shut off
First I replace the Radiant Flame Sensor, but the problem remain. Then replace the two coils and the igniter. Dryer works like it should. If I were to do it over, I would have replaced all 4 components to start with. Thanks for good advice and great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Lake Geneva, WI
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Drier stopped heating up
Followed the easy to understand how to video. The drier was up and heating again in less then 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- diane from Oak forest, IL
- Parts Used:
- 279311
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
NO Heat in dryer
It Went well Part was very fragile
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betsy from Round Mountain, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dryer quit before clothes were dry except on the extra low setting. I got an E1 error reading
flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Huntington Beach, CA
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Dryer would not heat. No flame or gas
Remove lower bottom cover (two screws on bottom) with screw driver. Remove old radiant flame sensor from left side of tube with ignior by using socket wretch. Remove wires with needle nose pliers. Put new part in: put wires back on, insert part's lower tab into the tube ( there is a small slot) use socket wrench to tighten screw at top. Put bottom front panel back on and screw back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ambler, PA
- Parts Used:
- WP338906
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer will not get hot
Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Paso Robles, CA
- Parts Used:
- 279311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Starts and runs, no heat
Initially thought it was the thermal fuse since that has already been replaced twice before for the same type of problem. After replacing the fuse the same issue remained, so I did a little hunting on the internet and found some matrixes to help diagnose the issue. After a couple of minutes, I discovered it was the ignitor. I immediately ordered the part and received it in about 5 business days. Even though that took longer than previous orders (usually < 3 days), I was still happy to get the part at a MUCH cheaper price than available locally. Installation took about 5 minutes with only a 5/16" nut driver and we were back in business. Kind of glad it broke because the dryer needed a good de-linting and cleaning anyway. : )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Clifton, NJ
- Parts Used:
- 49621
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The leveling foot on my dryer broke.
We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.
Was this instruction helpful to you?
Thank you for voting!