MGD7100DC0 Maytag Dryer - Instructions

We followed the on-line video which was very helpful but it took longer for us. But the part didn't fix the problem, so we had to go back on line and research it some more only to find that the more common cure for our problem was the gas coils which were even easier to replace and that did fix the problem.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.

I ended up taking the entire dryer apart when I didn't need to, and it turns out it wasn't the Igniter Kit in the first place but the thermal fuse in the back. Was pretty simple to repair in any case however.

pull out lint screen, removed 2 screws. lifted top up. removed 2 screws from the front,disconnected wiring harness. removed the drum and belt. located and removed the igniter, sensor, and coil valves. replaced all with new parts. reassembled. now it heats up. i believe that i only needed the coil valves. coil valves not shown on parts list, i purchased later. everything was very accessible with the drum removed.

Watched a brief video on YouTube and followed step by step. Real easy.

Replaced igniter

Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"

Followed the easy instructions on the video, and it worked. Sure beats calling a technician.

After getting on-line to your site we looked up what the problem could be after receiving the dryer from a friend to transfer from electric to gas to save money. First we thought it to be the ignitor and after receiving it so quickly it still didn't work so went to your site again and found the Flame sensor. They were both defective and now it works wonderful!!! Your site also explains what and how to repair the appliance, which my husband appreciated! We are glad you contacted us because your site did not show that we could send you and e-mail Thanking your company for the excellant service we received. Your prices can't compare to other companies either, we were amazed on the differences. When you say the next day delivery, you mean the next day!!! Thankyou and you are now in my Favorites if ever needing parts for other appliances we own.

Ordered thermal fuse and cycling thermostat

Since the power and gas to the dryer were both already turned off all I had to was open the top of the dryer, remove the front panel, look underneath the drying drum and remove the belt tensioner from the belt and slide the drying drum out. While things were open I took my vacuum and vacuumed all the lint, dirt and loose articles from over time out of the dryer interior. I located the igniter, used a nut driver to remove one screw pulled the igniter from its housing and disconnected the wiring harness. For installation I reversed the process and I was done. I reinstalled the drying drum, reattached the belt tensioner, put the front panel back in place and closed the dryer top. Attached the dryer vent hose, plugged the dryer to the electrical outlet, turned on the gas and walla it purred like a kitten. It even seem to dry faster than before.

unplugged dryer and removed front panel. removed the screw that holds flame sensor and unplugged electrical wires. then replaced with new. Did not solve problem so I ordered the replacement coil kit and installed them using phillips screw driver and this solved problem. Dryer is working fine now. I found this site very helpful and would recommend it to a friend.

Took the back dryer cover off and removed the lint cover all from the back of the dryer then replaces the Thermistor (held with 2 screws).

Pretty easy to fix, hardest part was having to get the screws out of the inside of the dryer to replace the sensor itself. Once that was done it was pretty quick! PLUS super fast shipping on my part!! Was fixed before any repair places even called me back!!