MGDB750YW2 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from ETTERS, PA
- Parts Used:
- WP8544737
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The fan wheel had a blade break off, my bad.
I went on the site and found the part I needed and then watched the video explaining how to dismantle, replace the part, and put the dryer back together. It was easy, especially with the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from FRUITA, CO
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic retainer on catch was broken
Used screwdriver to remove old catch as shown via video from manufacture and snapped in new catch. Very easy to do and saved big bucks by doing myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LANA from INDIANAPOLIS, IN
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Door would not clisr
Had to force the old door catch out using the putty knife didn't work. Worked on it until I finally forced it out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from MEQUON, WI
- Parts Used:
- W10239307
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Door seal came off
Did not take the door off..applied adhesive and seal fit perfectly..used packaging wide tape to secure for a bit while adhesive dried..waited 24 hrs..holding well..dryer is back to working order..thank you..I received the seal in 2 days after ordering!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from CARROLLTON, GA
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door wouldn't shut
Looked up on the internet, saw a video, ordered the part using model of dryer, got the part in 7 days, took out old part and snapped in the new door latch. Now it works good as new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from GAINESVILLE, FL
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broken
Push in new catch...close door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Forrest from PARIS, TN
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door Catch broken
Took Putty Trowel and pried out top and bottom then pulled out with needle nose pliers, new part just pops back in (be sure flanges are on top and bottom not sides).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURNDALE, MA
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch on dryer stopped catching (meaning the door would not stay closed)
I placed the putty knife on the top part of the door catch and when that came loose I placed the putty knife on the bottom of the door catch and pushed on the putty knife and the door catch came out of its place. I then just popped the new door catch in place. Total repair time 45 seconds. The door now closes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from FRISCO, TX
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door catch was broken
Took a screwdriver and bent wings out a little and then was able to get hold of it with a pair of pliers. Then just put the new unit in the opening and tapped it in. If I had a good pair of needle pliers, it would not have been necessary for the screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annie from HENDERSON, NV
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The door catch on our Whirlpool Dryer had given out.
The repair cost us less than $9.00 and about 1 minute to repair. You can only imagine how much a tech would have charged us!! We are so very happy that we discovered this site . The instruction video they offered, the customer service via their website AND quick delivery of the part, has insured them that we will be repeat customers. Thanks so much !!!!! Bravo! Annie & Peter in , Nevada
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from FORSYTH, MO
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
door catch broken and fell into door
snapped new catch into door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Polly from POTTSVILLE, AR
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broken
Didn't have a putty knife, so used a flathead screwdriver to carefully pop out the top, then bottom of the catch. New one easily popped in. Took less than one minute!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from butte, MT
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
would ignite but not run for more than 10 min.
Unplug unit turn off gas, remove only bottom front panel first tried radient flame sensor was not the problem it was the coils which were infront easy to acess with small screw driver remove two prong coil and replaced then the three pronged coil being sure to line them back before tigtening left off cover and watched for ignition once it turned on and ran replaced cover and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from W TERRE HAUTE, IN
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch Replacement
Used a screwdriver to pry out the bottom of the latch then the top. Pulled old latch out, then snapped new one in. Super Simple fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SCOTTSDALE, AZ
- Parts Used:
- W10120998
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Torn filter seal
Remove old filter, throw it away, replace with new filter.
Was this instruction helpful to you?
Thank you for voting!