MGD6000AG0 Maytag Dryer - Instructions

Checked fuse with Volmeter, had continuity (acted as a short) not the problem. Disconnected Hot Surface Igniter 2 Position connector to check resistance for a range of 50-300 Ohms of resistance with Voltohm Meter. Meter read open (High Resistance). Removed Igniter by unscrewing 5/16" hex nut on igniter plate assembly and noticed silicon carbide element was cracked in the middle. Ordered a new igniter and noticed assembly was required. Be careful here as igniter element is fragile, also do not touch it with your bare hands. You have to lay down on floor to reinstall igniter assembly and you might want to practice anchoring the defective igniter to gain confidence. Finally with slow movements anchored new igniter assembly and turned on dryer. Watched igniter glow heating gas valve and heating gas flame returned. Dryer fixed for a few hours of study online and cost only $24, plus learned how the gas dryer works.

Took the old parts out and installed the new parts in , everything that you sent fit perfect!!!!!

Unplug dryer from 220VAC outlet

Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.

Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together. You may need a small flat blade screwdriver to seperate connector.

Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.

Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.

Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.

Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.

Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.

At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.

Install new tensioner, tighten slightly, then put springs back on.

Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.

This dryer was quieter than its owners remembered it being back when new 15 years ago.

Well worth saving the $ doing your own work.

Good luck on your repair endeavor!

Removed the dryer door, unscrewed lint vent.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

Take pictures along the way.
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.

Glass door was broken with part still in door.
-put tape on glass so it would not fall on me as I dissembled door.
-removed and disassembled door by removing all screws/ torx.
-used shop vac to get most of the shards out then flushed with water for the rest.
-used shop vac to dry door.
-put back together. remember to put big bulge of glass down. the rounded part of the door is the bottom. do not over tighten as the screws go into plastic.
-all skill levels can do this job. it will only go together one way. the glass has a notch bulge that alines with the bracket. worst case is you have to put it together 3 times before you get it right. the door is reversible so it can open either to the right or the left giving you four combinations on how to install the glass. don't over tighten the phillips as they go into plastic. Go for it.

I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.

Since it was a dryer filter, it just had to be put in the dryer. Works GREAT!!

Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pulley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.

Replaced 4 wheels and new belt

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

Ezee pezee lemon squeezee.