MEDC300XW1 Maytag Dryer - Instructions

Pulled the dryer away from the wall took back cover off the dryer. Used volt/ohm meter to identify the bad element. Ordered the element it came in two days. 2 screws and 2 wires to plug in and we were back to drying cloths

It's amazing... I fixed my dryer!! I am a 47 year old woman with no technical training, and I did it!

I live in a apartment and I bought the Whirlpool Dryer (Model #LER7646JQ0) USED for $150 about 6 months ago. The dryer started blowing cold air, so I called the place that I bought it from and they quoted me a price of at least $300 to fix the dryer.

After searching through google, I found the partselect.com website, and read the repair stories. I decided to take a chance. I ordered just 2 of the suggest 4 parts that could fix the issue, and the dryer did not work. The next day I order the other 2 parts, and that did it - my dryer was fixed.

The diagrams on the site were a little confusing to me (the dryers looks a little simpler inside) but it was easy to repair. I used a screw driver and plier to do the repair, however it would have been much easier if I had a socket set. I would suggest buying all parts suggested, and return the items you don't need. Here are the parts I used:

1. THRMST-FIX (Thermostat, High Limit 221 F
2. USE WPL 279838 (Heating Element (10" long x 6" wide)
3. Thermal Cut-Off Kit
4. Cycling Thermostat (Limit: 155-25) (Thermostat, Internal-Bias)

Good Luck!

I removed the hex head screws from the back of the dryer and removed the back panel, after unplugging the dryer. I tested the various electrical components until I found that the upper limit temp fuse had gone out. Came to partselect.com and found the kit I needed and ordered it. When it came in, I replaced the upper temp limit fuse, and the other parts that came with the kit. I also, since the back was open, used the opportunity to vacuum out the blower fan and as much of the lint as I could get to. Dryer works great now!

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

Followed the video instructions that I was directed to through this site. The time it took me includes the time I used to vacuum out the back of the dryer and remove lint build up. The repair was very easy since the video provides all the information you need in an easy to follow format. I used my cell phone and paused when I needed to. Great site, great access to parts and great service. My parts were delivered in 2 days!

Removed two screws from lint trap and pried front of top up gently. Top hinges backwards which is convienent. Two more screws take the front off. Removed drum and old parts. Removed rollers etc. Per the instructions. Cleaned inside of unit with a shop vac.

Reassemble unit and test. Nice and quiet again and working well. Great service fro. Partselect.com.

Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.

First only replaced the high temp cut off switch which allowed the element to heat. However, after one heat cycle the switch would not reset. Then changed the thermostat (included in the kit). After tapping the cut off switch lightly to manually reset it, the dryer ran perfectly. Moral of the story: always change all parts included with a repair kit!

The replacement parts are truly easy to exchange. Everything is located behind the rear panel. A few fasteners needed to be undone. What's really important is another video that explained what should be "checked" when a dryer malfunctions. VERY IMPORTANT viewing. I spent an afternoon going over the front inside and rear of my dryer. I'll probably get another ten years from my dryer thanks to this site data and videos.

Good

Your video of the door switch replacement makes this job easy! My recommendation watch the video and you will have the switch replaced in a short time! My dryer was older than the dryer in the video but the principal of repair is the same! My new switch replacement fixed my dryer so when the door is opened the dryer shuts off!

Still wouldn't work! Push switch returned to you but have not received a refund yet. The repair was very easy. Tracking # 1Z 2R5 3A2 03 0025 9453 for returned switch.

















3

Sent for a new timer and installed it in less than 15 minutes and now dryer timer works just fine again

After replacing many, many parts the dryer still does not work! Replaced Thermo Fuse, Thermostate, Cycling Thermostat, Coils, Ingition Sensor and Ignitor. Ran meters across all incoming power, timer control, ignitor power, etc. all check out according to schematic. Incoming gas supply is functioning. So, 6 parts recommended later still same problem. On the good side, all parts were shipped out very quickly. Highly impressed with service.

I followed the instructions that I watched on the video. The video was very helpful.