MEDC200XW1 Maytag Dryer - Instructions

pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.

I typed in on my brouser Repair Kitchen Aid Dryer door switch.
And on You Tube up came several videos showing me how to ewmove the switch and install the new one.

The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away from the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada

Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to take the time to remove dust and lint from behind the dryer. Easy repair.

I disassembled the dryer once to clean the motor and compartment. After reasembly, the problem persistes. I ordered the motor and the second diasasssembly was accomplished in 10 minutes and the entire job took 45 minutes and the dryer was running like new. Tip- Leave the motor secured while removing the blower fan.

with both hands

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

First I unplugged the dryer from 240V and removed the back cover upper (behind the switch) and lower (exposing the remainder of the parts)

Inside the upper section was a folded wiring diagram of the dryer (don't know if this was courtesy of Whirlpool or another individual, but it was a very nice touch.)

I did a resistance measurement across the heating coil and found out it was fine. I then plugged the dryer back in and carefully took voltage measurements from one phase of power (this was easily accessed where the power comes in to the dryer, just be careful not to touch or short the wires)

I had an assistant turn on the dryer (this makes things go a little faster, as you are behind the dryer otherwise) and checked for 240V across the heater coil.

Once I did not have this, I kept one lead on the left side wire (one of the power phases coming into the dryer) and moved the other lead to the left (as viewed on the wiring diagram) until I no longer had 240V. This identified the faulty component as the Thermostat High-Limit, non resetable.

I ordered the kit with the High Limit NR and High limit Thermostat (as both had to be bad). I also ordered the 150 degree cycling thermostat (although this was not necessary - for <$20 I opted to replace it as well)

Removing wires one at a time, each component is fairly easy to replace.

My only complaint is that with the combo kit, the wire attachment is a little different that the original component and requires you to cut an existing wire and crimp a different terminal to allow all three wires on the High Limit thermostat (250 degrees) to be attached. There is little to show you how exactly the crimp is to be connected (it goes on the smaller of the three wires - DO NOT CUT the jumper provided and USE A GOOD CRIMPER - not the $2 variety, or you'll be getting a new connector!!) The connector provided is designed for some strain relief from one connector to the other, however) An additional jumper with the appropriate connectors already attached would be a nicer design.

Also, make sure you do NOT screw in the smaller cover that covers the power in until you place the entire lower half cover back on the dryer (unless you want to take it off a second time, as I did...) as it uses a common screw to hold both in place.

Overall, fairly easy to do with a minimum of tools, straight blade screwdriver to remove stubborn wire connectors (esp. for HT thermostat 250), ratchet and socket for quick removal and replacement of covers, and a good T&B style crimper ($10-$20 at your local hardware and well worth it even if you only use it a couple of times)

30 minutes and done - the dryer now cranks out the heat and the advanced settings (Auto dry) work great - no more 2-3 times throug to get things dry.

If you have a minimum of mechanical ability and a little bit of electronic troubleshooting skill, you can check and repair this youself and save about an $80-$100 service call.

Thanks to Part Select for the diagram of the dryer layout as well!! (Schematic would be nice if available online, though!)

Shipped the part in about 2 days from order time, as well. Will be back (hopefully not soon, though, as something has to break first!!!)

Be safe and good luck!

(One last note: Make sure your lint trap is clear including the hose - either due to build up or a lazy kid...as this probably caused the failure as heat could not escape...)

Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.

Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.

Unplugged washer,removed the two screws by the lint trap,moved the top foward lifted the top (it'shinged in the back )the switch is right inside the door top right hand corner removed the two screws that hold the switch in place used a flatblade screwdriver to seperate the connections pulled off the old installed the new switch put every thing back together worked as though it wes never broken

It was so easy... Pop out the old with flatblade screw driver and insert new piece... Works perfectly and looks better than the velcro strip I was using to hold the door shut...! Thanks for fast delivery and having the part available...

Regards,
JBL

Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.

After researching and finding correct replacement unit placed order and waited to receive. Screen is located top of dryer so replacement simple and fit was perfect.

just slide the new filter in.

Replacing the part was easy: unscrew the old one from the front of the dryer after opening door, disconnect and replace with new one. Getting to it was a bit more difficult: Remove 6 screws from the back, 4 that hold the back of the top down and 2 that hold the control panel in place. You had to remove the control panel to free up the wiring bundle (held in place by a tie wrap inside the control panel housing) so you could move the top forwards enough. Then remove the top of the dryer by lifting the back up slightly and moving it forward to disconnect from attachments in the front and move aside to gain access to the switch.

Boyfriend stated it was simple, he removed the back and replaced the part using a few everyday tools.