MEDB855DC3 Maytag Dryer - Instructions

Removed the front lower skirt with two 1/4"hex screws. Vaccumed all inner parts exposed. Removed three 1/4" screws holding the blower housing.Memoved the bias thermister again two 1/4" screws. Make sure all inner exaust pipes and rear chimney gas or electric are clean and lint free. Re assemble and test the unit. Install the skirt and make sure the dryer is level Jack, Pa.

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

1. Disconnect power cord and remove flexible duct. 2. Tilt dryer back and lean against wall, using folded towel to prevent wall damage. 3. Remove front/bottom panel - 4 screws on front/bottom of dryer. 4. Make alignment marks on internal vent duct where it attaches to vent bottom duct housing. Remove internal vent duct screw (towards front/top of duct) and slide vent duct out back of dryer (duct has to be removed to remove back panel) 5. Remove top panel (4 screws on back/top). 6. Remove AC power terminal block from back panel, disconnecting wire that restricts free movement of terminal block. Remove power cord from terminal block (3 nuts). Remove back panel (many screws). 7. From rear of dryer, gain access to idler pulley spring arm. Carefully note how belt routes around motor pulley and idler pulley (maybe record an image). Release belt from idler pulley. 8. Remove idler pulley triangle retainer (if still on pulley shaft) and remove old pulley. 9. Thoroughly vacuum lint and dust from all areas of dryer, internal duct, flexible duct and duct in wall (as far as possible) while dryer is in disassembled state. 10. Thoroughly clean idler pulley shaft of deposits with cloth. If desired, add very small amount of Park Tools Polylube 1000 to the cleaned shaft. 11. Install new washer, idler pulley and triangle retainer to shaft. 12. Re-route belt around pulley in original orientation. 13. Reassemble rear panel to dryer, terminal block to rear panel, and power cable and internal wire to terminal block. 14. Reassemble top cover to dryer. 15. Insert internal duct back into front vent duct, aligning guide marks, and secure with the one screw. 16. Plug unit in and briefly test, then unplug. 17. Again, tilt dryer against wall and reinstall front/bottom panel and screws. 18. Install flexible duct, plug in power cord and position unit for operation.

I removed the back of the dryer and then unscrewed the thermostat and fuse from the heating element shield and replaced with new ones. I simply reattached the back and did a test drying run. Good news, no overheating. Easy-Peasy

Thank you for your part service. It saved me about $ 200.00 dollars by Sears not coming out to repair a simple problem.

Took off front bottom panel reached in removed part that was very dusty. Put in new part. Cleaned out lint inside dryer. Works like a charm.

My way of replacing the pulley was much faster than the parts select video that showed how to replace the belt tension-er pulley. They took off the door, the entire front AND the drum to get to the pulley. I ACCESSED THE PULLEY BY REMOVING THE 4 INCH EXHAUST PIPE, (ONE SCREW) WHICH GAVE MORE THAN ENOUGH OPENING TO REPLACE THE NEARBY PULLEY! I suggest you remake that video

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

Removed existing parts and replaced with new high limit thermostat and thermal fuse kit,replaced flue and tested. Worked like a charm.

Dryer was making intermittent squealing noises sometimes it was amazingly loud, sometimes not so bad. Still, I figured this couldn't be good so I wanted to find a fix. Read the stories here and everything pointed to the 'idler pulley', so I figured I'd give it a try. For me, access was the hardest part -- my laundry room is small and I can't easily get the dryer out or move it around. Not a problem with the part, just my own setup. Important to note that this repair is best done through the BACK of the unit, not the front. Once I got access to the back (removing AC and Water used for the 'steam dry feature') I also had to disconnect several of the electrical connectors to get the unit fully apart. Good news -- the actual replacement of the pulley took about 1 minute! It was just all of the moving and disassembly that took so long. The original idler pulley had worked its way off of the shaft and was out of place and causing the squealing. All is well now, and I saved a bunch by doing it myself. No more squealing!

Ordered the fuse first hoping it was just that simple, watched the video for how to replace, first step was to take the back of the dryer off, well I order to take the back off I had to take off the Electrical Cord, as well as he top of the dryer. Only to find out he part I was replacing was not back there. Found the tech sheet attached within he dryer though, and as it turns out only needed to take he front bottom panel off. Without testing he continuity I was just giving this a shot, the Thermal fuse did no fix it, so I tried the high Limit Thermostat and Fuse kit still no luck. Took out the Element to find I was physically cracked in 2 pieces, replaced that and I was back up and running. And all parts were found in the bottom front panel of the dryer, so beware before you watch the video and take our whole dryer apart like I did.

First tried repairing the old idler by cleaning and lubricating the shaft. That lasted for about a week but the squealing returned. Ordered the part and had it in a few days. Replaced the idler wheel and it's been quietly running like new for several weeks now. Now wife thinks I'm Superman.

Had previously replaced the heater coil (purchased from PartSelect) and fixed the no heat problem. Should have taken advice given on this site and replace the thermostat and thermal fuse kit at that time. Since I knew how to remove the assembly it was easier this time. Just remove, unscrew the two parts and replace with the new ones. Reattach the wires and reinstall the assembly and it is now working again. Also vacumed the inside and trimed and replaced the exhast vent hookup for less restriction.

Disconnected the power and duct from the dryer. Removed the back and top of the dryer by removing the 1/4" screws. Created slack in the belt by compressing the spring and moving the idler arm.Slid the belt off the pulley. Removed the tri-ring clip, slid the old pulley and gasket off. Cleaned and inspected the shaft and vacuumed the inside of the dryer. replaced the gasket, pulley and tri-ring clip. Replaced the top and back of the dryer. Connected duct and power.

Removed the top panel of the dryer via a couple of screws from the rear. Remove the rear panel swing it open light a door to the right, minding the electrical connections. Removed the belt from the pulley, removed the Tri-ring from the shaft and slid the pulley off of the shaft. The shaft was slightly rusted so I used a steel brush and brake cleaner to clean it up, placed the new gasket, pulley, and tri-ring on, replaced the belt, and put the panels back into place. As the dryer is about 7 years old, also removed the front lower panel and cleaned out unit which had quite a bit of accumulated dust and glitter especially in the vent lines. (3 girls live here). Pretty easy, most screws remove with just the one tool.