MEDB835DW2 Maytag Dryer - Instructions

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

First tried repairing the old idler by cleaning and lubricating the shaft. That lasted for about a week but the squealing returned. Ordered the part and had it in a few days. Replaced the idler wheel and it's been quietly running like new for several weeks now. Now wife thinks I'm Superman.

Had previously replaced the heater coil (purchased from PartSelect) and fixed the no heat problem. Should have taken advice given on this site and replace the thermostat and thermal fuse kit at that time. Since I knew how to remove the assembly it was easier this time. Just remove, unscrew the two parts and replace with the new ones. Reattach the wires and reinstall the assembly and it is now working again. Also vacumed the inside and trimed and replaced the exhast vent hookup for less restriction.

Disconnected the power and duct from the dryer. Removed the back and top of the dryer by removing the 1/4" screws. Created slack in the belt by compressing the spring and moving the idler arm.Slid the belt off the pulley. Removed the tri-ring clip, slid the old pulley and gasket off. Cleaned and inspected the shaft and vacuumed the inside of the dryer. replaced the gasket, pulley and tri-ring clip. Replaced the top and back of the dryer. Connected duct and power.

Removed the top panel of the dryer via a couple of screws from the rear. Remove the rear panel swing it open light a door to the right, minding the electrical connections. Removed the belt from the pulley, removed the Tri-ring from the shaft and slid the pulley off of the shaft. The shaft was slightly rusted so I used a steel brush and brake cleaner to clean it up, placed the new gasket, pulley, and tri-ring on, replaced the belt, and put the panels back into place. As the dryer is about 7 years old, also removed the front lower panel and cleaned out unit which had quite a bit of accumulated dust and glitter especially in the vent lines. (3 girls live here). Pretty easy, most screws remove with just the one tool.

The repair went great . Thanks for the part ,will be purchasing parts from you now on.

Took the back dryer cover off and removed the lint cover all from the back of the dryer then replaces the Thermistor (held with 2 screws).

We did repair by first watching a you tube video, then jumping in an dgoing step by step through the video. While not exactly the same dryer, the steps were in sequence. We thoroughly sleaned out the dryer with the tub out before reassembly. Th eonly slightly tricky part was putting front piece back, but once we mad esure ot align the sides for squareness the dryer went back together smoothly, execpt for one dropped screw. that was fished out through the bottom panel. The dryer runs quietly and we can watch TV with the door open to the laundry room again. I should have done this a long time ago. It started out by sqeaking at startup, then grew worse over time. I recomend anyone with a friend should be able to do this. Now with Cell phone pictures it is even easier to remember where the screw go.

Removed existing parts and replaced with new high limit thermostat and thermal fuse kit,replaced flue and tested. Worked like a charm.

I removed the back of the dryer and then unscrewed the thermostat and fuse from the heating element shield and replaced with new ones. I simply reattached the back and did a test drying run. Good news, no overheating. Easy-Peasy

Thank you for your part service. It saved me about $ 200.00 dollars by Sears not coming out to repair a simple problem.

Using some advice here on this website, and a youtube video found by searching for 'idler pulley replacement' I was able to fix my dryer! Taking off the screws was simple, I used a cordless drill. I have some trouble removing the kick panel, and bent the latches, so there is a small gap between the dryer door panel and the kick panel, but it still works fine. Of note, you DO NOT need to remove the back panel, something I did and cost me some time. I am a bigger guy, so maneuvering on the floor to rig the dryer belt around the new idler pulley "in the dark" was cumbersome, but doable. All in all, an easy enough project for under $30 and less than an hour of my time. Kudos to this website, first, for the super fast shipping, and secondly, the reviewers who posted some instruction. Great job!

Disconnect the dryer from the power source and vent hose. Using the nut driver, remove all hex screws and the electric access panel from back of dryer. Loosen the electrical service cable clamp screws with philips screw driver and disconnect the ground wire. Remove the top panel from the dryer cabinet and the screws that hold the electrical bus in place, then remove the back panel from the dryer. Feed the electrical cable through the cable clamp and rest the back of the dryer against the side. Remove the tri-ring and old idler pulley, then clean and lubricate (WD40) the axel, and install the new pulley and tri-ring. Replace the back panel and all screws.

Took off front bottom panel reached in removed part that was very dusty. Put in new part. Cleaned out lint inside dryer. Works like a charm.