MED6000AW0 Maytag Dryer - Instructions

Pulled the back panel off with nut driver , reached in removed belt from pulley , disconnected the spring , removed the the 1 bolt holding the bracket .
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!

Lint can build up inside the dryer, and can cause a fire in EXTREME cases. If your model has a back panel that exposes the entire chute, this job is much easier. Unscrew the chute from the machine to remove it. Inspect and clean all the lint out, especially the bottom, next to the fan blower. The other version machine has a panel at the top that is welded on. Remove the two screws at the top corner of the rear bulkhead, where the chute is. Gently pull this inner panel away to free the top of the chute from the rear top panel. Then pull the chute down and out. Follow the reverse to complete the job.

Followed the instructions on your video.

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I am a retired applaince repairman not recommended for amature to repair this model.

Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.

Removed the front lower skirt with two 1/4"hex screws. Vaccumed all inner parts exposed. Removed three 1/4" screws holding the blower housing.Memoved the bias thermister again two 1/4" screws. Make sure all inner exaust pipes and rear chimney gas or electric are clean and lint free. Re assemble and test the unit. Install the skirt and make sure the dryer is level Jack, Pa.

diognostic suggested thermal fuse or thermistor. Thermistor tested low resistance (<2K olms). Replaced thermistor and dryer heat returned.

Our Dryer was no longer heating, upon opening the bottom of the dryer, there was a large amount dryer lint in the bottom. I cleaned it out and found the coil was no longer heating. Order parts from Partselect.com The parts were a perfect match! Identical to the original parts. The repair was simple once I decided to remove the back of the dryer. A lot of screws but with a driver it went quickly.

The videos really make it easy. I put my laptop on the washer next to my dryer and proceeded step by step. I also found the video that mentioned about the screws that may come loose on the baffles. I found several loose screws on the baffles which I tightened and I also found the Drum hole plug loose, so I also tightened the plug. Reassembled the unit and has been working like new since.

Opened machine up, removed electric control panel, removed door assembly, removed lint collector assembly, removed and replaced 2 sensor bars then reassembled machine. Ended up not being the problem but, I now have new moisture sensing bars.

Called a appliance place. They said it was a serious problem with master board and it was gonna cost 425.00 dollars. NO THANKS. Ten minutes to open ten minutes to find the problem. ( which was no were near the master board). Seconds to find and order the parts on partselect.com. got it next day. 15 to 30 minutes later my dryers running like it was brand new! Love it.

flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.

Pretty easy to fix, hardest part was having to get the screws out of the inside of the dryer to replace the sensor itself. Once that was done it was pretty quick! PLUS super fast shipping on my part!! Was fixed before any repair places even called me back!!