MED7100DW0 Maytag Dryer - Instructions

I ordered the maintenance kit because it was recomended for my application and the symptoms my dryer was exhibiting. However this kit did not apply to my model. My model contained 4 drum rollers, only 2 came with the kit, and the idler pulley setup was completely different. I should have pulled the dryer apart first to compare pictures to the actual parts. No big deal, prompt refund after a quick phone call to Parts select. I was able to fix my idler pulley with a couple of new nylon washers and a new snap ring to hold it in place. Whirlpool cabrio wed6200sw1.

Followed instructions that came with part.

Replaced with parts orded worked fine for2 hours and quit heating again

The instructions were easy to follow and the pulley on the replacement part was evenbetter quality than the original. I also followed the recommendation to clean the lint trap. Now the dryer works quieter and better than it ever did. Thanks for your product!

parts were for a dryer that would not tumble or heat they did not fix problem have called in pro hope he can fix

Removed the front lower skirt with two 1/4"hex screws. Vaccumed all inner parts exposed. Removed three 1/4" screws holding the blower housing.Memoved the bias thermister again two 1/4" screws. Make sure all inner exaust pipes and rear chimney gas or electric are clean and lint free. Re assemble and test the unit. Install the skirt and make sure the dryer is level Jack, Pa.

After running the unit for a minute or so I removed the back of the dryer. Unable to locate the problem from this vantage point, I then removed the bottom kick plate. Using a small flash light, and turning the drum by hand I discovered that one of the support rollers had burned out the bearings. I went to this web site to see if I could still get parts for the unit. I found not only the part, but a full repair kit. Knowing all the parts would need to be replaced at some point, and that Mom could not afford a new unit I replaced everything. The parts did truly arrive in one day when they arrived I went back to your web site. I had seen instructional videos while looking for the repair parts. After watching the video I removed the dryer drum, removed the parts to be replaced (2 drum support rollers the belt tension roller, and belt) I replaced old with new cleaned entire unit reassembled and it is working like a champ thank you very much for all the parts, and info

Opened up the dryer and found that the belt broke. Came to this web-sight and was quickly directed to the correct part once viewing the schematics, and then watched the video. The day the parts arrived in the mail, I went to work and managed to get the drying working that night! Thank you for the parts, the video...made it very easy to complete. Sheral

diognostic suggested thermal fuse or thermistor. Thermistor tested low resistance (<2K olms). Replaced thermistor and dryer heat returned.

Followed the directions on the web site. made a hook out of a wire hanger to hold the drum in place (hook from the back frame to the front of the drum) while I set the belt tensioner in place. removed the hook and the rest was easy.Works Great!!! like a new machine.

Ordered a parts kit with belt, tensioner, rollers, & clips, but did not use. Unfortunately, the kit was not correct for this model, regardless of the sales reps assurances. The kit had two rollers, our unit has four. The belt tensioner was not even close to being the same. However, a thorough cleaning of the interior with vacuum and rag was done. Removed, cleaned, and lubed each of the four rollers and the tensioner wheel as well. Lubed with small amounts of sewing machine oil on the axles and light spray of silicone on plastic to plastic contact points. Voila! It's as quiet as new.

flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.

Had to order idler lever and wheel as the one in the kit would not work. Best to buy part specific for your dryer. Repair was easy, just watch repair video. Sounds like new dryer again

Removed existing parts and replaced with new high limit thermostat and thermal fuse kit,replaced flue and tested. Worked like a charm.

Using a stiff putty knife I depressed the clips that hold the top down. I loosened the screws at the lower edge of the front panel and removed the two 5/16 head screws that hold the front on. I unplugged the door switch and lifted the front off the lower screws. I removed the drum and the broken belt. I replaced the rear rollers after applying some dry lube to the shafts and replaced the tension spring and rolled. I replaced the drum and belt and attached the belt to the small pulley on the motor. Then checked the rear gasket felt and reinstalled the front cover and the top.