MDG17PDAXW2 Maytag Dryer - Instructions

I had two dryers, one was gas and the other was electric. The electric stopped heating. So I rolled out the gas dryer, but it was setup for natural gas and at this location, I only have propane. So I changed the jets to work with propane, in the process I broke the igniter, so I replaced that and that made the propane one work. Armed with the knowledge from that job, I took the electric dryer apart located the thermostat and replaced that and low and behold I have two working dryers. One for now and one for an emergency. I only have four screws left over!!!! Jim Cooke

Just like your video said. Very easy. I will purchase from you again. Thank you!!!!

Just follow the repair video, it was easy!

Removed old door switch and tested with ohms meter. It registered as charged, but when black button was pushed it did not cut off (go to zero). Replaced the part just like the video showed. Only problem i had was dropping my screwdriver down into the dryer well. It was doing no harm so i left it there since i tried retrieving from the back but was not able to get entire back off!

I removed the two screws underneath the lent trap the removed the two screws that held the dryer switch assembly. I then lifted up the top and disconnected the door switch assembly. Removing the door switch assembly was the toughest part, and it was not difficult. Simply grab a pair of pliers and pull. I the attatched the new door switch assembly and the four screws and my dryerwas as good as new. I paid around $20.00 including shipping and saved myself a couple of hundred dollars

There are many good youtube Kenmore/Whirlpool door switch replacement demos online. The one already done by this site )was close enough for me. I could see that the door switch on my dryer was bad (the plastic part that the door makes contact with was visibly broken, as seen from the outside) -- so I ordered a new one. You don't have to open the top fully to access the switch wiring harness -- i propped it open with a roll of duct tape, The hardest part for me was to disconnect the old switch from the harness (I used a small flat bladed screwdriver to free it). Be careful, the metal inside the opened dryer is sharp, and can cut you.

Noticed the door switch was loose and the light bulb inside dryer didn't stay on. Researched the problem on PartSelect. Followed the directions given: Take 2 screws out of top of lint trap. Pry top off of dryer with putty knife. Unscrew 2 screws in dryer door frame holding in old switch. Uplug and remove old switch. Plug in new switch and put screws back in. Close top of dryer. Reinsert 2 screws in lint trap. My 20 yearn old dryer works!

First removed lint screen, then removed screws holding lint screen housing.Pushed on back of machine a little so that top could be pried up. Then replaced switch and put everything back together. Helps to have two people so one can push on back of top piece while top of machine is being pried up.

I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.

Kill power to dryer from breaker box.Remove lint filter & 2 screws. Take a flat head screw driver and place in gap between rash from corner of top panel & front panel of dryer and pry up to raise top panel of dryer & rest against wall the wall on angle do it doesn’t fall back toward you. Unplug wiring harness from dryer switch inside top front corner of dryer with outside of drum exposed when top panel of dryer is raised. Open dryer door and remove screws on each side of dryer switch located at upper inside corner of door opening. Take flat head screwdriver had slide in between connector & wiring harness on dryer. Remove old switch. Reconnect new dryer switch to wiring harness & remount switch to inside of dryer door opening. Lower top panel of dryer & press front corners of top panel to front panel of dryer & clips will be locked in place. Replace screws in dryer filter mounting holes yo top panel & replace dryer filter in place. Turn on power ‘ & check if light is working 1st. Then, turn timer knob clockwise, close door and listen if the drum is turning. Open door to see if drum turns. If both work, the job is complete.

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

had to take front off of Dryer then was able to replace drum roller

I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.