MEDX6STBW1 Maytag Dryer - Instructions

Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)

I followed the video. So easy..

Removed old seal and replaced with new one. Save yourself time and get some acetone to remove old glue works great!

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.

unplugged the electrical cord, took the back off the drier, unplugged wires from the bad heat unit. took couple of screws out that hed it in place, removed it , installed the new one plugged wires back , put the back on , plugged in electric cord. turned it on and that was all , works great. the part you guys sent was identical to the original . thanks. Ken

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

unplugged the dryer-- opened the back of dryer--tested the element--found there was a break in the element--ordered a new element--put everything back togethered and it worked. 10 screws held the back wall on--2 screws and 2 wires to disconnect the element---not very difficult!!

Simply checked the thermostats for conductivity and found that they were working properly. Removed the heating element to check for conductivity and discovered a broken coil. If I had the part ready to go the whole process from taking off the first screw to replacing the element to screwing on the last screw would have taken less than 15 minutes. Very simple repair that I almost paid a service technician an additional amount for something that a novice DYI'er could do.

I actually bought $254 worth of parts almost to point of rebuilding , which included both roller axles, drum belt, idler pulley, both rollers, the cloth that wraps around the drum for edging, and light bulb. 15 years before this the heater element and thermostat and the belt. This dryer is 27 years old and still being used on a daily basis. The mechanical parts and no LED components can last a life time. The wife always wants new, but this dryer with alittle love and patience is a workhorse. I'm thankful for websites like this. The videos are helpful! Thank you Parts Select! Sincerely, MIke Orkin

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.

Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.

Took apart front of cabinet, set aside. Undid the belt drive. Removed the drum. Noticed rear seal was with large gap where it wore away, causing the lint to leak onto the interior of cabinet. Ordered a new seal, removed old seal, prepped for new seal. Used spring clamp to hold new one on place. Applied the glue to hold seal in place waited 24 hrs to dry. Reinstalled drum, put cabinet back together. Plugged in ran whisper guiet.