LNC7749 Maytag Dryer - Instructions

Was a little hard getting at the idler pulley being it was behind the blower assembly, but it was the only draw back.

well, the hardest part is getting this thing apart - you have to take out the lint trap and remove the two screws from the top. Then I was trying to lift the top off - it's held in place by clips so you have to gently but firmly lift it off from the front end and let it open while still semi attached at the back (like a chest). Detach the electrical wires - they are just clipped in place. Then remove the screws (one on each side) that attach the front panel, and (and this is the hardest part if you don't know how it's attached). You have to SLIGHTLY LIFT the front straight up and then pull it away towards you. I just pulled it off, breaking the little attachers, which I subsequently had to weld back on with a welding compound and leave it overnight to set. the next day was pretty easy though...

The spinning drum is pretty easy to get out and you set it aside. Then I saw the belt pulley sitting there on the bottom of the dryer out of place -- fortunately with the belt there came instructions on how to instal it - READ THOSE INSTRUCTIONS - after that it's cake - put the belt around the center of the drum and feed it through the other parts underneath (this is easier if you tilt the dryer back a bit to get at it better. And you must pull back on that pulley after you have put it in place again - clips into the bottom of the dryer - it's supposed to have a lot of tension on it. Put it all back together and voila!

good luck!

Un pluged and Moved it out from the Wall, Raised the top, found broken belt. ordered belt on line, 2 days belt came in. cleaned all dust and dirt out put greese on berrings for rollers bleu out vent hose with Leef Blower. put top down, pushed back. pluged in and turned on IT WORKS!!!

Shut off power and gas, unscrewed lint vent, raised top on angle with rope, unscrewed and moved door switch, unscrewed and took off front, put new belt around drum, then raised front end of drum with 4 narrow pieces of 1" foam insulation which let me view and install the belt connection to the drive motor shaft, adjusted the level of the drum using the rope holding up the top, removed foam pieces, replaced and rescrewed the front to fit the drum front channel, replaced the door switch, replaced the top and screwed it to the lint vent, returned gas and power, and ran confirmation test.

I watched an online video about how to replace a dryer belt & followed the directions. Placing the belt around the drum is easy but stringing it thru the pulley is a little difficult because the belt has tension. This takes a little effort but is doable. Dryer runs great now........Be sure to unplug appliance 1st........

I followed the posted directions from others, and it was a breeze. They were really helpful. I would just add the step of keeping the drum in place with a block of wood underneath before removing the front. Slip the belt around the drum, reattach the front , and then finish positioning and tensioning the belt once the block is out of the way .

Unplugged the 220 line, removed lint cover, (2 screws). Lifted top with a screw driver, (2 plastic fasteners) then unplugged a ground line at the front lip to separate the front panel. There was a 50/50 chance here that I would not put the wires back correctly, didn't not make note of the color differences. There was no lower panel, just a single panel on the front, which I first tried to remove like the top, but quickly saw no results, then lifted the panel easily, which I set aside. I rested the drum on a 4x4 piece of wood. I then slipped the new belt over the drum, aligned the bulkhead at the rear, and positioned the belt in the original position, there was a distinct mark showing this. Next I saw the idler pulley lying on it's side, hmm, thought this might take some time, but the illustrated instructions were very accurate, reset the pulley, pushed it toward the motor and doubled the belt around the pulley, it sort of felt right, according to the grooves on the floor panel. I then rotated the drum counter clockwise, then tested. It worked! Became a hero to my wife and found $1.86 in change, woo hoo! Total cost, including shipping under $20., two day delivery, amazing. Thanks.

I pulled the old one off and put the new one on. It took about 3 minutes because I also replaced the old lint filter.

First unplug the machine and turn off the gas. Then, I pried the top up (2 clamps on front, 2 screws to the lint screen). Then I removed 2 5/16 nuts that fastened front panel to sides. I held the drum and pried the front panel back while my wife slipped the new belt around the drum. Then, I buttoned everything back up in reverse order, removed the kick panel, threaded the belt through the tensioner pulley and around the motor shaft. It's really that easy. PartSelect.com makes it simple with quick, accurate service.

Needed a belt. Only snag was for me was re-installing front panel (door)

Watched a video and went to town taking it apart. I stuck a pop can under the barrel to hold it up while I worked on pulleys. My dryer does not have a plastic pulley but a metal tension bar with a hole in the middle. Ran upstairs and watched a different video with my set up and all was good. 5 min of work 5 min watching Youtube and 5 min cleaning all the lint out of the machine. I am actually glad the old belt broke because some of the lint was in a clump and had scorch marks on it. I took the shop vac to every part of the cabinet and shoved it down the lint trap sleeve also.

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

DISCONNECT THE POWER. Double check the dryer is unplugged. Use a putty knife to free the latches holding the top of the dryer in place. Lift up the top of the dryer and secure it in place (be sure it's safely held open and won't come crashing down onto yourself as you work). Remove the two screws on the inside and near the top of the dryer, which hold the front and side panels. Gently lift up on the front panel (it may help to open the dryer door to get a better grip). Once free from the bottom clips, carefully rotate the front panel so that the door sensor wires are not strained. Once the front panel is out of the way, grab the drum and firmly lift it up and away from the back. (The drum has rollers and ridges at the rear and you'll need to pull the drum out of its "track"). Slide the new belt around the drum and position the drum about halfway inside the dryer. Loop the belt around the motor, but not the tensioner, (it will be easier to install the drum if you wait to tension the belt). With the belt around the motor, gently slide the drum back keeping the belt around the motor pulley. Press and guide the drum back onto the rollers at the rear. Check the belt is positioned correctly around the drum and motor. Reach back from the front and loop the belt around the tensioner. Rotate the drum by hand and make sure the belt is aligned and the drum spins smoothly. Position the front panel and slide it onto the lower clips. Install the screws being very careful not to drop them into the abyss... Close the lid and plug in the power.

Just slid the new filter in.

Disconnect power. Removed front panel and lifted top. Removed belt around spring pully and motor assembly. Carefully eased belt around back of drum and gasket. Reverse process.