4GMEDC100YQ0 Maytag Dryer - Instructions

The (front) bearing and seal are not metal parts but a fabric and and mesh like material. It is somewhat like a fabric belt made to hold up a pair of trousers. The belt sits in a channel that goes around the door on the inside of the front panel. To get to the combination bearing/seal you remove two screws that are located under the cover of the lint trap. These have to be removed to lift the top. Then using a putty knife or screw driver you must pop the top (which snaps down on plastic clips) at the front corners. The top lifts up and folds back on hinges. The front is attached to the sides by one screw on each side near the top. A nut driver will remove then easily. Once the 2 screws are removed lift the front panel about 2 inches to disengage the front panel from the clips that hold the front attached to the sides near the bottom. When you remove the front panel the dryer drum will literally fall out so you want to get hold of it before pulling the front panel away so it isn't damaged and and doesn't damage the gas burner assembly which is under the drum to the left side. The drum is very light. I supported it with an empty shoe box while the front was off.
Once the front is off you'll see the bearing/seal on the inside of the front panel and it will be obvious how to remove the old one and place the new one. There are three pegs on the front panel that receive the three holes in the fabric bearing/seal. The seal will stay in place while you remove the shoe box and put the front cover back on. The drum fits over the seal like a lid on a jar and just slides on the fabric when the drum rotates. Low tech but the drums slides easily on the bearing material and seems to last a long time.

I also did the rear dryer seal. This is similar to the front. To do this you follow the procedure above but to get to the real seal you will have to remove the drum. It will fall out on its own if the front panel is removed. The drive belt goes around the drum. It is about 3/8th of and wide and just wraps around the drum without any teeth or channels or anything. Let the belt fall to the bottom as you lift the drum forward and out of the cabinet. The drum is light. Just put it on the floor and strip off the old rear seal which is glued on. It too is fabric. Clean up the drum a little and fit the new seal on the drum. Once the seal is on the drum you can lift the edge of the fabric seal and glue the fabric flange to the drum. This becomes pretty obvious once you have the seal on the drum. If you put the glue on the drum first you will make a mess. Put the seal on properly and the lift the edge to apply the adhesive all the way around. The adhesive sets enough in a hour or so. Put the drum back in and replace the front panel. Don't forget the drive belt. It goes around the drive motor that is located on the bottom of the dryer on the right, around or over an idler pulley (my older model does not have a idler wheel but rather a bracket with a "slide" that the belt runs over that keeps sufficient tension on the belt to drive the drum. If your belt falls off the motor and the idler pulley falls out it may be confusing how the belt goes in. My idler bracket is held in slots on the bottom of the cabinet merely by the tension of the belt - no screws or anything. I suggest that you put the belt around the drum first, then the drive motor. You will have slack in the belt and it becomes a little more obvious how the idler pulley (which is mounted on spring steel) goes in and takes up that slack and keeps modest tension on the belt. The rubber side of the belt goes against the drum, the leathery side is the outside.

i decided to order the new element which was the most expensive part then decided to add the thermostats just incase they were bad because they were rather inexpensive. got the parts in took the back off the dryer located the parts i ordered and simply replaced them with the power cut off to the unit. put the back on and it heated like it was better that new my clothes dry 5 times faster than it did when i bought the thing.

super fast shipping, got the part in two days, and had it done in 15-20 min, remove the front pannel, remove the belt and tenssioner,took the drum out , took the old rollers , lubed the shafts,replaced the old rollers with the new ones, intalled the drum back, the tenssioner and the new belt, reinstalled the front pannel, and done...easy and fast job, like new dryer, works nice...save some money...the new one will do the same..just dry the clothes.

Lint filter supplied by Parts Select was an exact replacement by an aftermarket manufacturer. I put the old one and the new one side by side and they were identical (of course, the handle wasn't broken off on the new one!). I coulnd't be happier. It arrived at my house 2 days after I ordered it. I highly recommend Parts Select.

I wasn't sure if I was going to be able to do the repair myself. Happily, I was able to and my dryer works like new ! I figure I probably saved about a 100 bucks doing it myself rather than calling out a repair man. Oh, did I mention I am female and didn't have to have a man do this for me. :)

Pryed the top off the dryer, unplugged the door switch, took the screws out of the front panel, then lifted the drum out. Placed the new belt around the drum and while my wife held it in place and steadied it, I reached underneath and looped the belt through (as per instructions), reassembled and back in business! Reaching under the drum was not that easy....VERY tight space to work in and there was no way I could get both hands through, I almost gave up, but one last try and a couple of good grunts, and it popped into place. Getting the wires back on the door switch was a bit of an ordeal too. Took about 30 mins. but still worth it. I'm sure I saved at least a $100 repair.

I took a ¼ inch nut driver and removed the rear cover from the unit, and then used a continuity tester to determine which safety device was open. According to the schematic there was one non-resettable safety device in the heating circuit, and that was open. The kit that I ordered came with thermal cutoff and a thermostat. I replaced both parts and the unit now operates normally. While I had the dryer open I thoroughly cleaned the dust and lint from the unit and also the 4 inch vent pipe. I ordered this part on Friday morning and received it early Saturday afternoon.

It was so easy, that my wife did it the day we got the part before I got home from work. She wedged it out with a flat head screw driver and then pushed the new door catch assembly in with her thumb. Pretty simple, thanks for having parts like this available to the public!

I ordered up a new heating coil. It was plug and play, real easy to do. Make sure to turn on the dryer with the before you put it back together to make sure the heating coils heat up. Be careful though, it will get real hot, so run for a second or two. Also, you may see a little smoke as the coil burns in, that should be fine. Once it is tested and works, let it cool off, then reattach it, put on the backplate and you are done!

I removed the four screws holding the
heating element, then I pulled the element out
and then put the new element in and hucked
the wires from the old element after I disconnected
them to the new element..no problem......

1. UNPLUG 2.Undo 8 screws @ back of dryer. Locate heating element midway down on right about 6"x10" has three thermostat wires connected to it undo the 2 screws & 3 wires either order. You will need to pry up GENTLY on the thermostat on the old element. Replace themostat to new element and make a test run to make sure its running and HOTand repeat steps in reverse order...

Took the back off with a cordless drill with an apex holder. I unplugged the old wires from the old heating element and plugged them into the new heating element. Put the back back on after testing it to make sure it worked and that was it. Since this element was in a housing it was really simple to reinstall the new one.

Local stores did not have any in supply. Went to Partselect and located lint screen, ordered, received in 3 days. replaced screen, Wife now happy again...

It was really quite esy remove the screws from the back and pop the top off . then remove 2 top inside screws from the front , lift the front off the sides , support the drum and lift out , you will then see the idler wheels, replace them with the new ones ,replce the tensioner , wrap the belt around the drum, need help putting the drum back in the case, have someone hold the drum in place while you lay on the ground and put the belt around the motor pulley and the tensioner on the bottom.you then put the front panel back into place and secure with the 2 inside screws, then put the rest back together in reverse oder. ... hope this helps someone

First my son and I moved the dryer to the garage as we believed there would be a lot of lint possible during disassembly. Used a flat head screwdriver to pop the top from dryer housing. Then removing 2 nuts to facilitate the removal of the front of the dryer. The drum was able to be removed to diagnose the offending drum roller wheel. The drum roller wheel has experienced a failure as it had melted off of the metal spacer. Removing it and replacing with the new one was pretty easy. We then used a shop vac and an air hose to clean out all the lint, coins, paper clips and lost jewelry. Surprisingly there was not a single sock in there. Put it all back together in reverse order and plugged it in and now spins like a dream.