4GMEDC300YW2 Maytag Dryer - Instructions

It required no tools, just take out the old torn filter and slip in the new one. I should have ordered it a year ago, with the ease of the website and the delivery via Fed Ex. super easy.

I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

Take the door off of the dryer. Lay it on a towel. Remove old gasket. Clean the channel the door gasket fits into with glue remover. Squeeze high temperature glue into the channel, let the glue set up. Put the new gasket into the channel, tape it down in a few places. Let it sit 24 hours for the glue to set up. Put the door back on. You can put the door on immediately as long as you don't use the dryer for 24 hours. Easy.

I actually bought $254 worth of parts almost to point of rebuilding , which included both roller axles, drum belt, idler pulley, both rollers, the cloth that wraps around the drum for edging, and light bulb. 15 years before this the heater element and thermostat and the belt. This dryer is 27 years old and still being used on a daily basis. The mechanical parts and no LED components can last a life time. The wife always wants new, but this dryer with alittle love and patience is a workhorse. I'm thankful for websites like this. The videos are helpful! Thank you Parts Select! Sincerely, MIke Orkin

Removed back and then removed lint slide.
Vacuumed all of the cabinet and and washed lint chute.
Blower seal and lint seals were crumbling since dryer is 24
years old. Part Select diagrams and repair videos are extremely helpful in showing the process. Dryer now working like new.

Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.

Took apart front of cabinet, set aside. Undid the belt drive. Removed the drum. Noticed rear seal was with large gap where it wore away, causing the lint to leak onto the interior of cabinet. Ordered a new seal, removed old seal, prepped for new seal. Used spring clamp to hold new one on place. Applied the glue to hold seal in place waited 24 hrs to dry. Reinstalled drum, put cabinet back together. Plugged in ran whisper guiet.

unplugged the dryer-- opened the back of dryer--tested the element--found there was a break in the element--ordered a new element--put everything back togethered and it worked. 10 screws held the back wall on--2 screws and 2 wires to disconnect the element---not very difficult!!

I put in the new parts but it still did not work, Turned out the Thermal Fuse Blew,removed the two wires and clipped them together and the Dryer worked, have to replace the Thermal fuse and everything will be OK.

first with the dryer unpluged ,i removed the wires from the upper thermal cut off ,then with a nut driver i removed it . replaced it with the new one and reattatched the two wires then the same on the bottom thermal . to replace the spring i removed the two screws pulled out the switch and spring at the same time ,removed the broken spring and replaced it onto the switch then placed it back into the dryer and replaced the screws.! everything worked like it han never been broke! my wife is verry happy!!!

Simply checked the thermostats for conductivity and found that they were working properly. Removed the heating element to check for conductivity and discovered a broken coil. If I had the part ready to go the whole process from taking off the first screw to replacing the element to screwing on the last screw would have taken less than 15 minutes. Very simple repair that I almost paid a service technician an additional amount for something that a novice DYI'er could do.

unplugged the electrical cord, took the back off the drier, unplugged wires from the bad heat unit. took couple of screws out that hed it in place, removed it , installed the new one plugged wires back , put the back on , plugged in electric cord. turned it on and that was all , works great. the part you guys sent was identical to the original . thanks. Ken

To be short and sweet, the repair was simple once I got the parts I ordered which came really quick. I put them on and it worked fine. Ez to install as well. It only takes half the time to dry, it seems to work better than when it was new. I saved hundreds. The repair man was going to charge $69.99 just to come out to see what the problem was. The parts I needed were under $100 so figured I'd try an do it myself, after reading others repair stories. I did it! I will be a repeat customers if something else breaks down. Thanks Partselect.

Removed top cover. Removed front cover. Removed Drum. Located the broken belt. Found that there was no tensioner in the unit. Replaced drum rollers. Put in new tensioner. Repaced Drum with belt around it. Installed belt through tensioner and onto drive pully of motor. Supported Drum with wood block. Turned on dryer to insure drum turned without any problems. Removed wood block. Replaced front cover and top cover. Repair compete.