4GMEDC300YW1 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eric from DELHI, NY
- Parts Used:
- 279816
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dryer runs, but won't heat.
First only replaced the high temp cut off switch which allowed the element to heat. However, after one heat cycle the switch would not reset. Then changed the thermostat (included in the kit). After tapping the cut off switch lightly to manually reset it, the dryer ran perfectly. Moral of the story: always change all parts included with a repair kit!
Was this instruction helpful to you?
Thank you for voting!
Intermittent heat issues
The replacement parts are truly easy to exchange. Everything is located behind the rear panel. A few fasteners needed to be undone. What's really important is another video that explained what should be "checked" when a dryer malfunctions. VERY IMPORTANT viewing. I spent an afternoon going over the front inside and rear of my dryer. I'll probably get another ten years from my dryer thanks to this site data and videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Eaton, OH
- Parts Used:
- 279816
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
No Heat
The dryer stopped heating, it would only blow cold air. I removed the back panel and tested the thermal fuse with a dmm. The fuse was open, so it was bad and I needed a new one. I tested the thermostat and the dmm measured continuity across the terminals, so I thought it was good, bad assumption. I ordered a thermal fuse from partsselect and it came with a thermostat. Like a dummy, I only installed the fuse. The 1st time I ran the dryer the fuse blew again, because the thermostat was bad. So, moral of the story, install both parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Dayton, TX
- Parts Used:
- W11778253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Filter wore out had to be replace
Changed out the lint filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from New Bedford, MA
- Parts Used:
- W11778253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken handle
1) removed the old broken filter
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from COCOA, FL
- Parts Used:
- WPW10314173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Roller Berings were worn out - replaced both
Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from BELTON, MO
- Parts Used:
- WP3979617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Dryer would not run unless I adjusted the timer switch manually
I simply removed the back panel (6 screws), removed old switch, swapped wires and reinstalled. Varied repair. That easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude from Austin, TX
- Parts Used:
- W11778253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Filter wore out.
It required no tools, just take out the old torn filter and slip in the new one. I should have ordered it a year ago, with the ease of the website and the delivery via Fed Ex. super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- linda from buckeye, AZ
- Parts Used:
- 279816
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dryer would work, didn't have any heat.
unpluged the dryer, took off the back, followed instructions and was able to take of the problem on my own.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evelyn from JACKSONVILLE, FL
- Parts Used:
- W11778253
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a new lint filter
Took the old one out, replaced it with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- diora from ROCKFORD, IL
- Parts Used:
- W10861521
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
wore out gasket
removed old gasket took door off 4 screws. cleaned seal area applied glue put on gasket easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from MILFORD, CT
- Parts Used:
- 4392065
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Broken belt
As seen in video, All Good !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TULELAKE, CA
- Parts Used:
- WPW10314173
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
dryer making noise. order parts
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Bakersfield, CA
- Parts Used:
- 279838
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Dryer ran with no heat
Dryer ran with no heat. Replaced the Thermal Fuse and when that didn't fix the problem discovered the element was burned. Easy fix except the F-disconnect fitting broke when I tried to remove it and male fitting on the heating element is 0.375 and all I could find were 0.250 F-disconnect fittings. I finally found a supplier who had a 0.375 fitting and the repair took 10 minutes after that. The online videos at PartSelect are excellent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Delafield, WI
- Parts Used:
- 279838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
burnt out heating element
removed back of dryer. Pull electical connections, removed heating element. Inserted replacement element, attached electrical connections and attached dryer back. Done -easily done.
Was this instruction helpful to you?
Thank you for voting!