4KMEDC100BQ1 Maytag Dryer - Instructions

Dropped new filter in.

Followed the included instructions in the Maintenance kit. Very easy to understand & follow. Only advice is to have an extra set of hands to assist in re-installing drum w/ the new belt. Entire disassembly & reassembly could be done w/ basic hand tools but went alot quicker using a cordless drill w/ a set of nut/screw driver bits.

Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and old belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!

I use the manentance kit that was not the problem. I end buying the drive motor and that was it. I was happy with the service I got from part select, overnight mail what more could I ask for? I am also glad I replace everthing with mainentance kit. Thank you for your help john degnan

Never did get the part. Initial order was not the right part. Ordered the right part on 12.2 and this is 12.18. While the initial oder and delivery was correct, they do not tell you that you do not have to ship by Fed ex. Fed Ex seems to not be able to provide service to our address despite driving past it several times a day.

It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him

I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.

With the instructional video the repair was very easy.

Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.

switched part out in 10 minutes. only needed to unplug appliance, disconnect wires, and 1/4 inch nut driver only tool needed.

The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.

Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding each one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.

Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.