4KMEDC425FW0 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from BEAVERCREEK, OH
- Parts Used:
- WP3977767
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
taking to long to dry
put the high limit in , plus the temperature , plus the exhaust switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from PARADISE, MT
- Parts Used:
- WPW10185982
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Easy
Took the back off with nut driver and took out defective timer. Then put in new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from COLUMBIA, MD
- Parts Used:
- W10861225
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Handle on the dryer broke
This was super simple - even I could do it! I followed the 3-step instructions which basically described how to hold the new handle and pushed it into the holes in the door. Less than 30 seconds and no tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Lindsay, CA
- Parts Used:
- 279441
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The dryer tub became jammed, unable to turn.
I followed disassembly directions found on youtube and replaced th two-piece ring bearing that was identified by a parts diagra fron PartSelect. The repair was easy. Fix time was about thirty mionutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larold from WILLMAR, MN
- Parts Used:
- WP3977767
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Dryer would not heat on any heat settings.
First I watched the repair video on-line at this site After pulling the dryer away from the wall and unplugging the 220 volt power cord I removed the back panel with the 9 screws. I then unplugged the wires to the thermostat/heating element. With an ohm meter I discovered that the heating element was good and the high limit thermostat was bad. I ordered the high limit thermostat from this site on a 2 day shipment. When the part arrived I installed the part and the wires. Plugged in the dryer for a quick check for heating. Replaced the back panel and moved the dryer back into position. Dryer works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from FAIRPORT, NY
- Parts Used:
- W11778253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Handle broke off of the Lint filter
Removed old filter and replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from KOKOMO, IN
- Parts Used:
- W11778253
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Handle broke
Placed lint filter in opening and pushed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy (Hairways) from WOODMERE, OH
- Parts Used:
- W11778253
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint screen had hole and looked like it was scorched
Just slide out lint remover and inserted new one. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carmen from CUSHING, ME
- Parts Used:
- W11778253
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Had a torn lint filter
Removed replacement from box. Threw old one out, the new one fit perfectly, and securely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- moujin from CARMEL, IN
- Parts Used:
- WP3977767
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
no heat only
repairing is pretty straightforward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from ENUMCLAW, WA
- Parts Used:
- W11429587
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
The plastic part on the door catch was broken
I removed the metal piece which held the plastic "catch". There were no screws, squeeze to remove it. Then inserted the plastic part and re-inserted the metal part into the dryer door. Very simple. But even more pleasing was the easy ordering and the quick delivery of the part! Thank you so much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Brenham, TX
- Parts Used:
- W11429587
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
broken plastic catch on dryer door
removed broken parts & snapped in new catch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from FAIR OAKS, CA
- Parts Used:
- WP3977767
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Unit was tripping the circuit breaker after about 10 minutes of drying time
Unplugged the unit, removed the back panel of the dryer and then removed the thermostat panel. Disconnected the wires on the thermostat and changed out the thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- West from Montgomery, AL
- Parts Used:
- W11778253
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
The handle would not seat" , with the old dryer lint slot. Had to remove the handle and leave the medal holder , to which the handle was popped on, by slot and hooks.
I inserted the sharp kniife point, pryed back a flap , thus releasing the nylon locking hook, in the slot. then did the other side...I removed the white plastic handle, leaving the metal frame, which lay more flat in the filter channel. I put a box of screws on top of the dryer flap to keep it snug.. this is a Kenmore about 15 years old.
Grahare
Grahare
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Shawnee, KS
- Parts Used:
- 3406839
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
I had only seen a one piece rack .The 2 piece threw me for a loop.
I thought I had checked the arm piece of the rack real good for a product number on my original part but I missed the number till the 2nd box came in, and a looked real careful and realized it was the same as the order I thought was bad.
Put the spring arm in first and the rack will fit in the front groove.
It would have been good if there had been a picture of the dryer arm attached to the dryer.
So I have 2 good racks and will return one if you tell me where to send it.
Keith Walden..
Put the spring arm in first and the rack will fit in the front groove.
It would have been good if there had been a picture of the dryer arm attached to the dryer.
So I have 2 good racks and will return one if you tell me where to send it.
Keith Walden..
Was this instruction helpful to you?
Thank you for voting!