7MMEDX550XW0 Maytag Dryer - Instructions

I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

1 screw to replace.

Had loud squealing prior knew rollers was going. Ordered repair kit that contained new belt , idle pully, and rollers. Knowing I had previously mended the door switch ordered a new to replace it. Unplugged and removed the dryer. Removed front lower panel, then the top and took the screws that held the front panel and door switch. Then I took the belt off and removed the drum. Removed the rear felt and cleaned the drum with fine mesh steel wool applied adehesive waited 5 mins and attached new felt. Then went to work cleaning the inside of the dryer with an air compressor. Rollers were next, poped the retainers and slide old ones off whiped the studs with a rag and put new ones on. Did the same with the belt tensioner pulley that came with the kit. Installed the new door switch and reassembled the dryer. Works great again, quiet etc. Easy fix and glad I ordered the kit.

Watched on-line video on how to disassemble and test heater element, thermostat, and hi-temp shut down. Heater element was open. Ordered new heater element. Re-installed heater element iaw video provided with parts. Video provide was one of the best I've seen. Explanation on releasing access panel was especially helpful.

Pulled the lower front panel located thermal switch pulled 2 wires removed 2 small bolts pulled switch out set meter to ohms scale and tested between the 2 terminals it hailed the test I reversed for installation of new switch

Took the back off the dryer. Found heating element unhooked the electrical connectors to the element,the high temp thermostat and the fuse backup. Opened the front kick plate, took the casing with element, ht thermostat and fuse bu out. Changed all three parts and reinstalled them. Turned on dryer and had heat. Been working great ever since.

Removed back panel of the dryer-reached my hand to the back of the motor shaft, put 7/16 wrench on it to hold the shaft while I removed the broken pulley with pliers. Very easy fix-the tech on Utube took the entire dryer apart totally unnecessary. If that is what the factory tells its tech"s to do its no wonder why the labor charge would be thru the roof.

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.

Disconnect power supply, remove power cord from dryer, remove dryer vent tube from dryer, remove 2 Philips screws from power connection on dryer, remove nuts from back of dryer, remove back of dryer. Locate idler pulley at bottom of unit at the rear of the motor, pull pulley back to loosen belt and remove from pulley, remove pulley retainer clip, remove pulley and rear washer from shaft and inspect shaft for wear or rust. replace washer and pulley (no specific direction to replace them, washer first then pulley). Reverse above procedure to reassemble. This is for a front load dryer, a top load dryer is different.

had to take front off of Dryer then was able to replace drum roller

Replaced the heating element. Took the front lower panel off, 2 screws one on each end, removed cover on left side over blower 3 screws and removed cover lower right side over heating element 2 screws. Removed 6 wires plugged into heating element cover, turned heater element cover counter clockwise and pulled out. Removed 1 screw holding heating element inside of cover, pulled out heating element. Replaced heating element back in cover putting screw back in to hold it. Put heating element and cover into hole in back of dryer turning clockwise to secure. Then put cover holding heating element over the front of it and secured with 2 screws. Put blower cover back secured with the 3 screws and put the front cover back on securing with 2 screws. dryer is heating better than ever.

Just replaced the old lint filter.

On this model do not try to remove the back. You must remove the bottom front panel and the lint screen unit. You can then loosen the heat coil assembly and rotate it to get to the high-limit thermostat and the thermal unit. I replaced both because I bought the kit. It actually took me longer to clean out lint than it did to replace the parts. A simple remove of the parts with a 1/4 inch nut driver did the trick. Now my dryer works fine.