7MMGDC300DW2 Maytag Dryer - Instructions

Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.

Took everything apart, replaced the igniter flint, and still didn't get heat. Then found out the thermal sensor wasn't running a electrical current through it with voltmeter and just replaced that, now it we have heat again!

Replacing the part was easy: unscrew the old one from the front of the dryer after opening door, disconnect and replace with new one. Getting to it was a bit more difficult: Remove 6 screws from the back, 4 that hold the back of the top down and 2 that hold the control panel in place. You had to remove the control panel to free up the wiring bundle (held in place by a tie wrap inside the control panel housing) so you could move the top forwards enough. Then remove the top of the dryer by lifting the back up slightly and moving it forward to disconnect from attachments in the front and move aside to gain access to the switch.

I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the glow plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

First, removed the bottom cover below the dryer door. This is just held on with two clips that can be pushed in with a flat screw driver. Then remove the springs that go from the bottom of the dryer to the inside of the dryer door. We had to remove the entire front of the dryer, so the easiest way we found was to loosen the two screws on the bottom of the front panel, but not remove them. Then pop up the top of the dryer. To lift the top, first remove the two screws under the little door where the lint trap goes. The top is hinged in the back, and it snaps down onto two clips that can easily be popped up with a flat screw driver) With the top opened, there are two screws accessible. When the front of the dryer is removed, there will be nothing to support the drum, so what we found was that if you rotate the drum, you'll find a point where there's a hole in the top of the drum. If you take the springs that you removed from the bottom of the door you can hook them into this hole, and hook the other end into a hole in the back wall of the dryer just behind the drum. The springs are the perfect size for this, and it keeps the drum from falling when you remove the front panel. then just disconnect the three wires going to the switch inside the front panel, and remove the two screws from the top of the front panel. It should then lift right off. The bearing can just be pulled away and the new one installed. Put everything together again in reverse order.

At first I was advised to replace the temperature overload sensors, which I did but didn't fix the problem. After adding the additional information that the dryer would run to full cycle as long as the Start switch was held in I was advised to replace the Start switch.

It wasn't obvious from the wiring diagram, but if you remove the Start switch and look at the side it shows it contains a solenoid holding circuit that keeps the switch in the "on" mode as long as there is a feedback signal from the temperature overload switches. So if the dryer will run to completion if the switch is held in, replace the Start switch. If it still stops mid-cycle, replace the temperature overload switches.

The replacement videos were spot on as far as clear and easy to follow instructions for the repair, and all ordered parts were delivered very quickly.

Thanks for your help PartsSelect!

PULLED THE DRYER APART TO GET TO THE MOTOR , REMOVED MOTOR , LOOKED FOR MODEL NUMBER OF DRYER AND DID RESEARCH ON WHERE TO BUY THE MOTOR AND BOUGHT FROM PARTS SELECT BECAUSE BOUGHT FROM THEM BEFORE

The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.

Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.

For the Ignitor - As involved as taking the dryer completely apart sounded, it was super easy. 1-take out the lint trap and remove the two screws there. 2-Pop open the top with a screw driver and swing the top completely over/back. 3- remove the two screws holding in the front panel and remove the panel. 4- loosen the belt by pushing on the tension roller under the drum on the right and remove the drum (its super light) use the belt as a handle. 5- remove the screw holding in the ignitor and replace it with the new one. Be careful to not touch the new ignitor. Then go backwards putting it back together.

Really simple, the dryer repair guy I had out did not have the part and wanted $100 to fix. Did it myself quickly and easily and the dryer is working like a charm.

1 screw to replace.

Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two screws. Plug in dryer and there you go drying clothes again. Wife all happy again.

Be very careful of burrs on the edges of the steel inside the dryer. I cut myself badly when reaching into unplug the switch.
Procedure: Lifted the dryer top by pulling forward and rotating front up. Removed 2 philips screws holding the switch at the door. Reached into dryer and unplugged bad switch. Inserting small blade screw driver at the edge helped release the plugs detent. Installed new switch using reverse of above.