7MMEDX655EW0 Maytag Dryer - Instructions

BEFORE ANYTHING ELSE UNPLUG THE POWER AND TURN OFF THE GAS SUPPLY 1. unscrew the 3 nut screws at the back to remove the cover lid. 2. pull the control console cable from the electronic board. (only 3 wires on it).3. unscrew the 2 nut screws of the control console then remove it by pulling up.4. unscrew the 5 screws to remove the door. (pull little up to unhinged then remove). 6. unscrew the 5 nut screws to remove the lower siding. 7. unscrew the copper 4 nut screws then remove the lint suction fixture 8. unscrew the 4 nut screws to remove door fixture ,then just lay next to the machine.(the wires are long enough so you don't need to unplug and separate it from the machine.9. remove the belt by pulling the idler pulley towards the motor pulley (against the tension spring) 10. remove the drum by lifting a little bit upward. 11. remove the plastic triangular lock using a small screw driver then remove the idler pulley wheel then install the replacement. (clean your machine using a vacuum cleaner and remove all the lints). 12. install back the drum, be sure to set the drum belt to the right position. (groove on drum side). 13. install back the belt to the pulley the same procedure as to remove it. 14. assemble back what you have removed. end.

When the problem first came up, I took the dryer apart without first looking up any instructions. This wasn't difficult, but didn't realize when removing the fan from the motor, there is a square lug as part of the fan hidden by the rear clamp securing the motor. I was able to remove the fan by holding the motor shaft with a crescent wrench and removing the fan by hand, but was difficult and gloves were necessary in case the fan loosened quickly and my hand came in contact with the sheet metal (very sharp).

I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.

This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.

The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.

My son got it in the mail for me and snapped it right back on.

PULLED THE DRYER APART TO GET TO THE MOTOR , REMOVED MOTOR , LOOKED FOR MODEL NUMBER OF DRYER AND DID RESEARCH ON WHERE TO BUY THE MOTOR AND BOUGHT FROM PARTS SELECT BECAUSE BOUGHT FROM THEM BEFORE

it took loess than 10 minutes to change the door switch after watching the repair video

Partselect order confirmation email included video instructions of how to change the door switch on my model dryer. Like others I had a pause with the switch connector. I viewed the video again and the instrucions showed to use the putty knife tip to push down on the connector tabs and it came right off. Replacing the switch was easy as the video instructions. Fast shipping of the right part at a good price. The video was pricless. Thank you partselect.

I typed in on my brouser Repair Kitchen Aid Dryer door switch.
And on You Tube up came several videos showing me how to ewmove the switch and install the new one.

The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away from the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada

Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to take the time to remove dust and lint from behind the dryer. Easy repair.

By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.

Just popped it into place needing no tools at all. Took less than a minute.

Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.

Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.

I disassembled the dryer once to clean the motor and compartment. After reasembly, the problem persistes. I ordered the motor and the second diasasssembly was accomplished in 10 minutes and the entire job took 45 minutes and the dryer was running like new. Tip- Leave the motor secured while removing the blower fan.

Both my husband and I are not good at DIY or fixing things. I watched the instruction video that was posted on the PartSelect web site. It seems easy to do it, however still very skeptical. My husband decided that there is nothing to lose in trying, so we ordered the parts. It is as easy and simple as the video instruction. We are very happy customers.

My dryer was running way too hot and the temperature settings didn't make any difference. Clothes were shrinking and coming out almost scalding hot. I followed simple directions posted on you tube for troubleshooting this problem. I checked that there were no lint blockages, visually inspected all connections and hardware. All seemed good. Metered out all thermostats and fuses. Everything checked good for continuity. For the reset-able thermostats, I heated them on a hot plate to verify that the normally closed switches opened near their specified temperatures. Dont do this for the non-resetable fuses and thermostats. If you're
not sure, avoid this step. Only the hi-limit thermostat seemed to open a little higher than expected but I couldn't with 100% accuracy determine the exact temp it opened. Made sure the heating element wasn't shorted in its housing or that too might give the dryer the same symptoms. That checked good too. Only thing left I could think of was to change that hi-limit thermostat. Ordered part, removed and replaced. Perfect fit. Op-checked good. All heat settings now operate normally. No more shrunken clothes that are too hot to touch even on the lowest setting lol. Hope this helps, happy hunting.

*as with all electrical repairs I unplugged dryer from the outlet*

I disconnected the wires to the heating element, removed the 2 nut screws holding the heating element in place and removed the defective heating element. It looked like the heating element had darkened on the lower end and the wire terminals definitely looked like they had built some resistance that lead to the connection wire melting.

I slid the new heating element in and replaced the 2 screws. I cut the melted portion of the connection wire about 1/2" beyond the melted area and stripped the wire jacket exposing clean wire. I took the connection kit & clean wire lead, divided the wires into 2 groups on each end and braided them together and twisted them to a hand tight grouping. I then took the lead cap and twisted into onto the braided wire connection until it was also hand tight and snug.

I then reconnected the heating element connection wire back to the terminal end of the heating element and made sure all connections were snug.

I plugged the dryer back in, reset the dryer by turning the dial to a timed setting then back to off. I set the heat to low turned the dial to a time dry and turned on the dryer to ensure the element heated up and that the wired connection was secure. After 20 - 30 seconds, the element maintained heat and no issues were found with the fixed wire.

I replaced the dryer back and all screws and reconnected the vent hose. Dryer has worked great for the last few weeks with no issues. I was really surprised it was that easy to fix.