7MMGDB850WL1 Maytag Dryer - Instructions

I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with the new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.

After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.

After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lot of time and money if I had read that earlier.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.

once the back is off remove belt from tentioner and remove v clip. smooth shaft with wd-40 and scotch brite , then install new idler replace v clip
and your done !!!

Took the old filter out and inserted the new one- works great!!

I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful

Very bad design to keep door shut but very simple to fix. Just screw bad strike out and screw new one end. Whirlpool should have gave extra when you buy this type dryer.

Pulled out the old and slid in the new filter

My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you

Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.

Like another reviewer's repair story, I decided to take the door apart. It was too difficult, at least for me, to get the faulty catch out without damaging either the the door or my hands. This is why I give it an "easy" rather than "very easy" rating and put the total repair time at a half hour or better. I also decided I wanted a second person to help - not with getting the door apart or putting it back together, but because a second pair arms was very helpful in rehanging the door well. We removed the door (four screws), marking which side of the hinge needed to be flush with the actual dryer when rehanging. Then we took the door apart, which comprises another sixteen screws (four on each edge). We used an electric drill but I'm sure it could be done manually. We used needle nosed pliers to get the faulty latch out of that side of the door, then replaced it with the "back up" from the other side. Then we put the door back together and carefully rehung it. Done. We did decide that, in future, all kids (we have three boys) slamming the door would be severely beaten. Pushing the door until it's against the dryer, then PUSHING (as opposed to slamming) the latch ONTO the catch pin on the dryer is obviously what was intended. However, I've learned not to count on my boys being particularly conscientious, so I'd ordered four replacement latches to keep on hand. This machine was delivered in April 2009 and I replaced the latch in April 2011. Based on this and our laundering habits, I'm sure the others will be used long before the dryer calls it quits.

Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.

Removed the broken catch with a pair of needle nose pliars and replaced it the same way. Took about 10 minutes. Saved a Service Call

We watched the video at whirlpool.com! Made it so simple anyone could have done it!