SDG5401AXW Maytag Dryer - Instructions

Remove the 2 screws at bottom of front panel, remove lower panel. Then remove the two screws at bottom of front door. Lift door forward so spring hooks can disengage from the top panel. remove door, disconnect the 5 wires to the door latch and light. remove the two screws at top of dryer to lift up top panel. Remove 4 screws at the front holding the drum. Disengage the belt from the tension pulley and remove drum. Replaced both roller wheels at the rear of the drum( one was broke). Then remove the screws (about 6 holding the plate in front of the blower wheel. Use a wrench to hold the nut at the back of the motor and a scocket wrench to remove blower wheel. (The Blower wheel was broken from the shaft and was spinning freely). Then do it all backwards to re assemble. i spent more time cleaning the lint from the inside than I took making the repair!

First I removed the four screws that hold the back cover of the control panel. I then disconnected the two wires from the buzzer and removed two screws holding the buzzer. Install the new buzzer.

After removing the front of the dryer, I took out the front assembly where the seal and glide brackets attatch. I replaced the bad cylinder glide by drilling the old rivets out and re-riveting the new glide in place from the back side. I then replaced the felt pads and glides on the glide brackets and glued a new cylinder seal around the front assembly. I reccomend having 4 hands for placing the cylinder seal around the assembly with fresh glue.

First, leaned dryer back and removed 2 screws at bottom front panel.
Then removed 2 screws at bottom of door assembly.
Pulled bottom door assembly forward and down.
Disconnected "can't go wrong" wiring connectors.
Then removed old cylinder glide rivets at bottom of cylinder using drill motor with 1/4" drill.
I installed new felt pads on new cylinder glides. Then installed glides with rivet gun.
Reconnected wire harness.
Installed door assembly and lower panel assembly.
BACK IN BUSINESS! THANK YOU!!!!!!!!!!

Not too difficult. Take out of box, insert into dryer slot.
Done

This is a gas dryer. I was able to access the thermostat through the small front access panel. Not easy to see but with a short nut driver I could take out the two screws. I was able to pull the thermostat to the front panel hole and switch the wires. Putting it back in was a challange since I had to do it by feel since I could not look and get my arm in at the same time. Suggest anyone that does this put a small piece of paper around the screw to hold it in the driver

Dryer would only tumble for ~15 min then stop. During this time it would be really loud. Turns out to be a bad Motor. To replace 1) Removed bottom kick panel by removing 2 screws. 2) Then removed upper front cover by 2 additional screws. 3) Disconnected thermostat (marking location of wires on paper). 4) Removed blower housing (3 screws)undid the rib belt from the drum by pushing the pulley wheel up so the belt could be loosened and removed from motor. 5)Removed the front cover of the dryer opening by removing 2 screws. 6) Lifted up and then puled it out to expose the drum. 7) Removed the drum w/belt from the dryer exposing the motor. 8) Removed 2 screws from the motor and disconnected the plug from it. Slid it all the way out. 9) Need to remove (3 screws) the metal faceplate from motor to access the blower wheel (plastic). 10) Unscrewed the plastic wheel and removed 2 screws to remove the motor from the frame. reversed the process for reassembly. Sounds tougher than it really was - only took 30-45 min. Suggestion - write down on paper location of any wires you disconnect - makes reassembly very easy. Also recommend vacuuming any lint in the dryer while it is completely accessible.

Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

1-Unplugged drier
2-removed lower panel-(2)-8mm screws
3-removed intake from fan-(3)-8mm screws
4-removed dryer's front panel-w/door assembly-(2)-8mm screws. (note there is a door switch you will need to disconnect the wires and remember which terminals they go to.
5-remove the front drum support-(4)-8mm screws
***** at this point the drum is exposed *****
6-reached under the drum pulled the tensioner to relieve tension on belt, then dismounted the belt from only the tensioner and motor shaft; leave the belt on the drum!
7-pull drum toward you and forward about 3-to-4 inches, this exposes the drum rollers.
8-use a screwdriver and pry-off the retaining clip on the end of the roller's shaft and remove the roller.
9-remove the roller support-(2)-8mm screws
10- reinstall new roller support
11- apply a light coat of disc-brake hi-temp wheel bearing grease to the roller support shaft, very light!
12-install a new wavy thrust washer, new roller(note they will say "front" on the side that should face you. Don't mount it backwards!
13-install the outer thrust washer and the new retaining clip; use a flashlight for this part!
14-repeat for the other drum roller.
**** while you have it apart use a vacuum to remove lint from every where you see it; it is a fire hazard!
**** if you think you need a drive belt now is the best time to change it *****
15- re-assemble the dryer in the reverse order, don't forget to re-install the drive belt and be careful not to pinch the door switch wires.
16-re-plug the drier and test

Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.

First I went to Maytag.com thinking it was best to go to the manufacturer for parts. Their search engine did not even recognize my part number. I tried every way I could think of. Then I just entered the model number in google and it sent me to the Partselect.com website. Diagrams came up and I chose parts from the pictures. The parts arrived in about 3 or 4 days and fit perfectly.

Replaced the recommended drum rollers, belt and tensioner, light bulb. Found repair manual online (bit of a hunt)made job easier still took 2.5 hrs. Then turned drum by hand no squeak. Turned it on and still squeaked. Isolated to motor. Replaced it (had to take dryer completely apart again but went quicker due to experience also had to disassemble the motor assy and rebuild. Took 1.5 hrs works like new now. The design of the dryer is not bad remove bottom front panel first, screws at very bottom of panel then two more screws are uncovered to remove front. It just lifts up and pulls out. then remove four bolts which hold front frame on (supports drum) all this has to be done to reach the replacement parts. drum wheels are held on by snap rings not the screws (real fun if you take them out) reverse to reassemble.

remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .

By following the directions included with the kit it was fairly clear. The diagrams of the control valve was helpful. It would have helped to tell which screws to remove to access the valve and where the screw was that retained the burner assembly.

Easy repair and done all from the front. Turn off the power at the breaker. Make sure the power is off. Remove 2 screws holding on the lower panel. Then remove 2 screws holding on the door panel. (Pay notice to the order in which the 3 door wires will get re-connected. The 2 light bulb wires probably can go either way.) Then remove 4 screws to a large bracket that supports the front of the drum. (Set these parts aside as you take out the screws.) Then remove the 2 screws from the top panel. Reach in under the drum and release the tension off the belt. It's easy to release, but sorta mind boggling to put back on. Maybe practice that once while it's fresh in your mind. When the belt is off the motor pulley, then lift out the drum. Vaccuum out a lint blanket if you have one. You'll see the 2 drum support rollers and the belt tensioner roller. I didn't know which was squeaking so I replaced all 3. Same method, use ring pliers to take off the retainer ring, remove old, wipe off dust, install new rollers, replace ring. Note the washers are different so put them back on in the same order as removed. Make sure the gasket on the lint assembly gets tucked nicely into the blower housing when you reassemble. Easy repair. If you do pull the dryer away from the wall, replace your flexible exhaust vent with the fire resistant aluminum version.