MDE3000AYW Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lonnie from Carlton, OR
- Parts Used:
- 33001790
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The dryer would rumble after startup.
We started by unplugging the unit thenremoving the door tand front panel.By removing the belt from the tensioner and lifting out the drum.the drum rollers were replaced first and rumble was still there when operated.Checking the blower wheel revealed a crack the width of the blower.After new blower was installed the dryer operated almost as quietly as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Rockvale, TN
- Parts Used:
- WP33002535, 12001541
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set, Wrench set
The dryer was overheating & making a loud noice
Took the entire dryer apart after watching a video online. Replaced the rollers & the belt & put dryer back together. Since I am a machine builder by trade I knew how to do some of this after watching the video, but not sure how easy this would be for someone untrained.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Rancho Palos Verdes, CA
- Parts Used:
- WP6-3700340, WPY312527, WP354987
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
loud squeaking noise with dryer running
watched the video.unpluged the power to the dryer disasembled the front of the cabinet removed the belt from the idler pulley and then removed the drum cleaned up the dust and lint in base of the cabinet and then removed the e-clip from the shaft on the idler arm removed the outer washer then worked off the pulley with pressure from a small flat blade screw driver removed the inside washer. cleaned the shaft and greased it with white lithum grease installed the first washer then the pulley then the out side washer then the e-clip but found that the pulley had a little side to side play removed pulley and installed one of the old washers on the inside along with the new one reasembled the pulley washer and e-clip the play was gone and the e-clip fit in the grove ok reasembled the cabinet and the noise was gone you could see the old bearing in the pulley was rusted
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Rancho Cordova, CA
- Parts Used:
- WP6-3700340, WP33002535, 12001541
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
squeeking
Pulled the front off. then the inner face and drum. removed belt and two pulleys and re-installed. took me 45 mins. never done it before. watch the video that comes with the parts confirmation you get online and do the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Exeter, RI
- Parts Used:
- WP33001755
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dryer Baffle had broken & needed replacement
Removed door &clips on latch side of door using a philips screw driver. Removed the dryer front panel by hand exposing the two metal clips holding down the dryer top panel. Using a nut driver, the two clips were removed allowing the top panel to be raised. The dryer drum was manually rotated to the location of the broken baffle. Using a nut driver, the broken baffle was removed. The new baffle was installed in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EF from Montvale, NJ
- Parts Used:
- WP33001621
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer time set dial cracked-- had to use pliers to move the dial and use dryer
Exactly as shown in your helpful video- took dial apart and replaced broken skirt with new one-- cost me only $15, saving at least $100 on service visit. Very happy with it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rommel from hercules, CA
- Parts Used:
- WP33001762
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas flame shutting down after a minute.
replaced both solenoids on the gas valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Dallas, TX
- Parts Used:
- WP33001621
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
knob broken
Remove old skirt and replaced with new skirt on timer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Manitowoc, WI
- Parts Used:
- WP33001621
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I could not the timer dial.
I followed the video. It was real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alana from Hampton, NH
- Parts Used:
- WP33001621
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer would not advance
This was an easy fix once I ordered the correct part. I snapped the cover off top and then separated skirt from knob. I then slide it onto the metal stem. I needed to remove a small black plastics piece in order for knob to go on fully. This must have broken off the old skirt. Extremely easy to do and the video was great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bend, OR
- Parts Used:
- WP6-3700340, WP6-3129480, WP33002535, 12001541
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Drying had starting making a loud screeching noise
The noise started intermittent and got worse. After watching an online repair of a very similar model and same brand, I decided to tackle it myself. The problem was that one of the drum support rollers had seized up. The shaft that support roller road on was also a little sticky. The noise was caused by the roller hitting the sheet metal behind the drum support roller and scraping on it. I replaced the shaft and drum roller and believe that solved the problem. I ordered other parts for the dryer drum assembly and replaced them while I had it apart. I didn't want to take it apart twice so I didn't take the time to disassemble to diagnose it. I just ordered them all and replaced them all while I was in there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Tallahassee, FL
- Parts Used:
- WP33001621
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer knob had cracked trying to turn a frozen timer
Pull dryer knob off. Separate the skirt from the knob and cover. (I also had to remove the rear panel in order to disconnect the wire to the dryer buzzer.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- E from San Francisco, CA
- Parts Used:
- WP33001808
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Torn lint filter
Remove the old on and pop in the new. Good time to vac the insides as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Boulder, CO
- Parts Used:
- WP307178
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer produced no heat.
I searched for possible symptoms and viewed a video about how to remove the heating element. There were three possible parts listed for this symptom: Thermostat, thermal coupling and heating element. I decided to check the heating element continuity, so I removed the heating element. Once I looked at the heating element, I could see a break in the heating coil, so I know the problem. I put my existing thermostat on the new heating element, plugged in 4 wires and installed two screws to secure the heating element, then reinstalled the front cover to the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Bedford, TX
- Parts Used:
- 12001541
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
It was making a lot of noises
IT was good My husband fixed it .sorry we didn't take video but it is working alright. Thank you
Was this instruction helpful to you?
Thank you for voting!