Models
>
DG308
DG308 Maytag Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for DG308
Viewing 10 of 10Keep searches simple, eg. "belt" or "pump".
$13.50
This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommen...
In Stock
$32.48
This is a single OEM dryer drum belt. It measures 100 inches in length, 3/8 of an inch wide and has five ribs and four grooves. Keep in mind that this rubber drum belt will stretch over time, so if yo...
In Stock
$14.70
This part is located on the front bulkhead of the dryer and helps the drum to rotate smoothly and quietly. If you notice a screeching or metal-on-metal noise while your appliance is operating, you may...
In Stock
$9.81
The roller shaft is also known as a support roller shaft or a drum roller axle. It is a part in your dryer that the drum rollers spin on, helping your dryer to tumble. If your appliance is noisy while...
In Stock
$22.88
The blower wheel is responsible for blowing heat into the dryer drum, and out of the exhaust vent. If you notice that your dryer is taking too long to dry or is make unusually loud noises, it may be t...
In Stock
$25.05
This lint filter is a genuine OEM replacement part for your dryer. The lint filter is used to trap debris and prevent it from clogging up your dryer vents. If your lint filter has become damaged it sh...
In Stock
$7.88
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is nois...
In Stock
$47.91
This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allo...
In Stock
$13.79
This roller shaft washer is just under an inch in diameter and is used for some of Whirlpool's brands of clothes dryers.Sold individually.
In Stock
$38.35
This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.
In Stock
$13.45
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
In Stock
NOTE: The manufacturer recommends that you replace the burner receptacle at the same time.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Terry
February 4, 2022
Won't run after the first load it will run later on
For model number DG308
Hello Terry, Thank you for the question. The Appliance could be over heating and then taking time to cool down. We suggest opening the cabinet and cleaning out any build up inside. Also clean the vents and the Lint Duct as this can be caused by poor air flow. If the issue persists, you can test both Cycling Thermostats and the High Limit Thermostat with a Multimeter to check the continuity. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Related Parts:
Common Problems and Symptoms for DG308
Viewing 11 of 11Noisy
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
noisy rollers, broken latch
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of t
... Read more
he front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job.
Thank you.
Thank you.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Lafayette, IN
- Parts Used:
- Y303836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The blower fan (nylon) stripped off the motor shaft (steel)
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from West Bend, WI
- Parts Used:
- WPY312959, Y303836, WP33001003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
electric dryer was rumbling - wheel or belt?
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through
... Read more
. Put the tumbler back on and reached back with both hands to thread it. Took a half dozen tries until I was sure it was seated correctly and not twisted. Put front... of dryer back on. So far (a week or so) the rumble is gone. Seems blower wheel was the cause of the rumble. Belt didn't seem worn but replaced anyhow.
Read less
Was this instruction helpful to you?
Thank you for voting!